2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

B1244 Light Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal, and outputs it to the main body ECU. The main body ECU turns on or off the headlights and taillights according to the signal.
DTC No.
DTC Detecting Condition
Trouble Area
B1244
  1. Malfunction in automatic light control sensor
  2. Open or short in automatic light control sensor circuit
  1. Automatic light control sensor
  2. Harness or connector
  3. Main body ECU (Instrument panel J/B)

WIRING DIAGRAM

E193002E03

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester main switch on.

  1. Select the item below in the DATA LIST, and read the display on the intelligent tester.

    Main Body (Main Body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Illuminate Rate
    Illumination rate information / 0 ms to 99.99 ms
    0.8 ms to 22.0 ms (Value is output according to ambient illuminance)
    -

    OK:
    Normal condition listed above is displayed.



OK
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
NG


2. CHECK VEHICLE CONDITION

Result:
Vehicle Condition
Proceed to
Manual Air Conditioning System
A
Automatic Air Conditioning System
B



B
Go to step 6
A


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)

  1. E193003E02
    Disconnect the h2 automatic light control sensor connector.

  1. Disconnect the E6 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-18 (CLTE) - h2-5 (CLTE)
    Always
    Below 1 Ω
    E6-19 (CLTS) - h2-4 (CLTS)
    Always
    Below 1 Ω
    E6-20 (CLTB) - h2-3 (CLTB)
    Always
    Below 1 Ω
    E6-18 (CLTE) - Body ground
    Always
    10 kΩ or higher
    E6-19 (CLTS) - Body ground
    Always
    10 kΩ or higher
    E6-20 (CLTB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Reconnect the main body ECU connector.

  1. E193004E02
    Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    h2-3 (CLTB) - h2-5 (CLTE)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    10 to 14 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    h2-5 (CLTE) - Body ground
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


5. INSPECT AUTOMATIC LIGHT CONTROL SENSOR

  1. E190278E02
    Reconnect the h2 automatic light control sensor connector.

  1. Connect an oscilloscope to the automatic light control sensor connector.

  1. B113714E01
    Check the waveform.

    OK:
    Tester Connection
    Tool Setting
    Condition
    Specified Condition
    h2-5 (CLTE) - h2-4 (CLTS)
    5 V/DIV., 5 ms./DIV.
    Ignition switch ON, light control switch in AUTO
    Correct waveform is as shown

    HINT:
    If the ambient light becomes brighter, width A becomes narrower.



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

6. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)

  1. E121476E09
    Disconnect the h1 automatic light control sensor connector.

  1. Disconnect the E6 main body ECU connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-18 (CLTE) - h1-3 (CLTE)
    Always
    Below 1 Ω
    E6-19 (CLTS) - h1-5 (CLTS)
    Always
    Below 1 Ω
    E6-20 (CLTB) - h1-6 (CLTB)
    Always
    Below 1 Ω
    E6-18 (CLTE) - Body ground
    Always
    10 kΩ or higher
    E6-19 (CLTS) - Body ground
    Always
    10 kΩ or higher
    E6-20 (CLTB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY )
  1. Reconnect the main body ECU connector.

  1. B109993E35
    Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    h1-6 (CLTB) - h1-3 (CLTE)
    Ignition switch off
    Below 1 V
    h1-6 (CLTB) - h1-3 (CLTE)
    Ignition switch ON
    10 to 14 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    h1-3 (CLTE) - Body ground
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


8. INSPECT AUTOMATIC LIGHT CONTROL SENSOR

  1. E121468E08
    Reconnect the h1 automatic light control sensor connector.

  1. Connect an oscilloscope to the automatic light control sensor connector.

  1. B113714E01
    Check the waveform.

    OK:
    Tester Connection
    Tool Setting
    Condition
    Specified Condition
    h1-3 (CLTE) - h1-5 (CLTS)
    5 V/DIV., 5 ms./DIV.
    Ignition switch on (IG), light control switch in AUTO
    Correct waveform is as shown

    HINT:
    If the ambient light becomes brighter, width A becomes narrower.



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


← B1244 Light Sensor Circuit Malfunction (Oct 2006 – May 2009)B2410 Headlight Swivel Motor LH Communication Malfunction (+ B2411) (from Oct 2006) →