2006-2011 Camry Aurion · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

  1. B136443E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.


2. REMOVE DOOR ASSIST GRIP COVER

  1. B149028E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the door assist grip cover.


3. REMOVE REAR ASH RECEPTACLE ASSEMBLY (w/ Ashtray)

  1. B136442
    Remove the rear ash receptacle assembly.


4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

  1. B136451
    Remove the 3 screws.

  1. Using a clip remover, disengage the 7 clips.

  1. B136452
    Raise the rear door trim board to disengage the 4 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.

  1. Disconnect the connector.

  1. B136453
    Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.

  1. B141704
    Disengage the clip as shown in the illustration and remove the No. 1 door scuff plate clamp from the rear door trim board.


5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

  1. B136457
    Using a screwdriver with the tip wrapped with protective tape, disengage the 2 claws and remove the rear power window regulator switch assembly.


6. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

  1. B136456
    Disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.


7. REMOVE REAR DOOR ARMREST BASE PANEL UPPER

  1. B136454
    Remove the 7 screws.

  1. Disengage the 4 claws and remove the rear door armrest base panel upper.


8. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

  1. B136459
    Disconnect the cables and remove the rear door inside handle sub-assembly.


9. REMOVE REAR DOOR SERVICE HOLE COVER

  1. B149017
    Disconnect the connector.

  1. Remove the rear door service hole cover.

    HINT:
    Remove the remaining tape on the door side.


10. REMOVE REAR DOOR CHECK ASSEMBLY

  1. B146084
    Remove the bolt, 2 nuts, and the rear door check assembly.


11. REMOVE REAR DOOR WEATHERSTRIP

  1. B146102
    Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.


12. REMOVE REAR DOOR GLASS RUN

  1. B136466
    Remove the rear door glass run.


13. REMOVE REAR DOOR FRAME GARNISH

  1. B136882
    Disengage the clip and remove the rear door frame garnish.


14. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

  1. B136467
    Remove the 2 bolts, the screw, and the rear door lower window frame sub-assembly.


15. REMOVE REAR DOOR QUARTER WINDOW GLASS

  1. B136468
    Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.


16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

  1. B146103
    Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


17. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B136472E01
    Disconnect the connector.

  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall, causing damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.

  1. Remove the temporary bolt from the rear door window regulator.


18. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

  1. B124520
    Using a "TORX" driver (T25), remove the 3 screws and the rear power window regulator motor assembly.


19. REMOVE REAR DOOR LOCK ASSEMBLY

  1. B136473
    Using a "TORX" socket wrench (T30), remove the 3 screws.

  1. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

  1. Remove the door lock wiring harness seal from the rear door lock assembly.


20. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

  1. B136475
    Using a screwdriver, disengage the claw.

    HINT:
    Tape the screwdriver tip before use.

  1. B136476
    Remove the rear door lock remote control cable assembly.


21. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

  1. B136477
    Using a screwdriver, disengage the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B136478
    Remove the rear door inside locking cable assembly.


22. REMOVE REAR DOOR OUTSIDE HANDLE COVER

  1. B136479
    Using a "TORX" socket wrench (T30), loosen the screw.

    HINT:
    The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

  1. B136480
    Disengage the 2 claws and remove the rear door outside handle cover.


23. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

  1. B124528
    Pull and hold the release plate of the outside handle frame as shown in the illustration.

    NOTICE:
    The release plate may interfere with the outside handle and may be damaged when removing the handle, unless the release plate of the outside handle frame is pulled and held.

  1. B136481
    Remove the rear door outside handle assembly as shown in the illustration.


24. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

  1. B136483
    Disengage the 3 claws and remove the rear door front outside handle pad.


25. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

  1. B136484
    Disengage the 2 claws and remove the rear door rear outside handle pad.


26. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

  1. B136485
    Using a "TORX" socket wrench (T30), remove the screw.

  1. Disengage the claw and remove the rear door outside handle frame sub-assembly.


27. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

  1. B137003E01
    Fully open the rear door glass.

  1. Put protective tape around the rear door belt moulding assembly.

  1. B137004
    Using a moulding remover, disengage the clip and 6 claws, and remove the rear door belt moulding assembly.

    HINT:
    Tape the remover tip before use.

    NOTICE:
    Be careful when removing the moulding as there are claws attached to the front end of the moulding.


28. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:
When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

Heating temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body and moulding excessively.

  1. Using a heat light, heat the rear door front window frame moulding.

  1. B137009
    Disengage the clip.

  1. B137010E01
    Using a moulding remover, remove the rear door front window frame moulding.


29. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

  1. B137012E01
    Put a 4 mm (0.16 in.) drill bit into a drill.

  1. Tape the drill bit without the portion of 5 mm (0.20 in.) from the tip covered.

    HINT:
    Tape the drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 7 rivets.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.
    3. Be careful when touching the drilled rivets, as they may become hot.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Remove the rear door upper window frame moulding from the door frame.


30. REMOVE REAR DOOR OUTSIDE STRIPE
  1. Using a heat light, heat the rear door outside stripe.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an edge of the rear door outside stripe and pull it parallel to the vehicle body to pull it off.


31. REMOVE REAR DOOR LOWER OUTSIDE STRIPE
  1. Using a heat light, heat the rear door lower outside stripe.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an edge of the rear door lower outside stripe and pull it parallel to the vehicle body to pull it off.

← ON-VEHICLE INSPECTION (from Jun 2006)DISASSEMBLY (Oct 2006 – May 2009) →