Rear Door UNLOCK Detection Switch LH Circuit
Circuit diagnosis · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The rear left door unlock detection switch is built into the rear left door lock assembly. The switch turns on when the rear left door is locked and turns off when the door is unlocked.The main body ECU (instrument panel J/B) is connected to the rear left door lock assembly via terminal LSWL (with smart entry and start system) or LSWP (without smart entry and start system) and rear left door lock/unlock state signals are input to the main body ECU (instrument panel J/B).
The main body ECU (instrument panel J/B) applies voltage to the door unlock detection switch via terminal LSWL (with smart entry and start system) or LSWP (without smart entry and start system). When the door unlock detection switch is on (there is continuity between the switch terminals), a lock state signal is input to the main body ECU (instrument panel J/B). When the switch is off (there is no continuity between the switch terminals), an unlock state signal is input.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Start the inspection from step 1 if the vehicle is equipped with only the smart entry and start system, or if the vehicle is not equipped with the smart entry and start system, but is equipped with the theft deterrent system. Start from step 2 if the vehicle is equipped with neither the smart entry and start system nor the theft deterrent system.
| 1. READ VALUE ON INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.

Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Select RL-Door Lock Pos SW in the DATA LIST and read the tester display.
Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RL-Door Lock Pos SW
Rear left door lock position switch signal / ON or OFF
ON: Rear left door lock is in UNLOCK position
OFF: Rear left door lock is in LOCK position
-
- OK:
- The display is as specified in the "Normal Condition" column.
|
|
||||
| OK | ||
| ||
| 2. INSPECT REAR DOOR LOCK ASSEMBLY (UNLOCK DETECTION SWITCH) |
Remove the rear door lock assembly LH (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Measurement Condition
Door Lock Condition
Specified Condition
6 - 9
Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1
Lock
10 kΩ or higher
6 - 9
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4
Unlock
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY - MAIN BODY ECU) |
Disconnect the main body ECU (instrument panel J/B)*2 or instrument panel J/B*1 connectors.


*1: with Smart Entry and Start System for RHD *2: without Smart Entry and Start System for RHD
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- with Smart Entry and Start System for RHD:
Tester Connection (Symbols)
Condition
Specified Condition
K5-6 (LSSR) - IP-5
Always
Below 1 Ω
K5-6 (LSSR) - Body ground
Always
10 kΩ or higher
K5-9 (E) - Body ground
Always
Below 1 Ω
- without Smart Entry and Start System for RHD:
Tester Connection (Symbols)
Condition
Specified Condition
K5-6 (LSSR) - E6-27 (LSWP)
Always
Below 1 Ω
K5-6 (LSSR) - Body ground
Always
10 kΩ or higher
K5-9 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
