2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


METER GAUGE

  1. without Multi-information Display
    E143771E01

  2. with Multi-information Display
    E143772E01

    METER GAUGE: 
    Item
    Detail
    Speedometer
    Indicates the vehicle speed receiving a signal from the skid control ECU. (CAN (CAN No. 1 Bus))
    Tachometer
    Indicates the engine speed based on a signal received from the ECM. (CAN (CAN No. 1 Bus))
    Engine Coolant Temperature Receiver Gauge
    Indicates the engine coolant temperature based on a signal received from the ECM. (CAN (CAN No. 1 Bus))
    Fuel Receiver Gauge
    Indicates the fuel level based on a signal the fuel sender gauge. (Direct Line)
    WARNING/INDICATOR: 
    Item
    Detail
    TURN SIGNAL
    Receives a turn signal from the turn signal flasher. (Direct Line)
    BEAM
    Receives a beam signal from the main body ECU. (CAN (CAN No. 1 Bus))
    CHARGE
    Receives a charge light signal from the generator. (Direct Line)
    CHECK E/G
    Receives a check engine light signal from the ECM. (Direct Line)
    DOOR
    Open door indicator light comes on receiving a door condition signal from the main body ECU. (CAN (CAN MS Bus))
    D-BELT
    Receives a driver side seat belt signal from the center airbag sensor assembly. (CAN (CAN No. 1 Bus))
    P-BELT (*5)
    Receives a passenger side seat belt signal from the front passenger seat belt buckle switch and transmits a passenger side seat belt condition signal to the clock assembly. (Direct Line)
    Fr FOG (*3)
    Receives a front fog indicator light from the main body ECU. (CAN (CAN No. 1 Bus))
    A/T SHIFT (*1)
    Receives an A/T shift condition and A/T gear position signal from the park/neutral position switch and the ECM. (CAN (CAN No. 1 Bus))
    FUEL
    Receives a fuel signal from the fuel sender gauge. (Direct Line)
    ABS
    Receives an ABS signal from the skid control ECU. (CAN (CAN No. 1 Bus))
    SLIP (*4)
    Receives a slip signal from the skid control ECU. (CAN (CAN No. 1 Bus))
    VSC (*4)
    Receives a VSC signal from the skid control ECU. (CAN (CAN No. 1 Bus))
    BRAKE
    Receives a brake signal from the brake fluid level warning switch (Direct Line) and the skid control ECU. (CAN (CAN No. 1 Bus))
    CRUISE
    Receives a cruise signal from the ECM. (CAN (CAN No. 1 Bus))
    AIRBAG
    Receives an airbag signal from the center airbag sensor assembly. (CAN (CAN No. 1 Bus))
    Oil pressure
    Receives an oil pressure signal from the engine oil pressure switch. (Direct Line)
    Speed limit (*5)
    1. Receives a vehicle speed signal from the skid control ECU.
    2. Meter CPU performs bulb check for 3 seconds when turn the ignition switch on (IG).
    H-LP LEVEL
    Receives a headlight leveling signal from the headlight leveling ECU (*6)

    HINT:
    1. The multi-information display has been located below the tachometer.
    2. The display shows a message for each of the functions described in the table below.

    MULTI-INFORMATION DISPLAY (*6): 
    Item
    Detail
    Cruise Information
    1. Outside Temperature
    2. Driving Range
    3. Average Fuel Consumption
    4. Distance driven since engine start
    5. Average speed since engine start
    5 types of information (outside temperature, driving range, average fuel consumption, distance driven since engine start and average speed) can be displayed.
    *1: for Automatic Transaxle
    *2: for Australia
    *3: with Front Fog Light
    *4: with VSC
    *5: for G.C.C. Countries
    *6: with Multi-information Display


MULTI-INFORMATION DISPLAY FLOW CHART (WITH MULTI-INFORMATION DISPLAY)
E128064E12

HINT:
Illustrations may differ from the actual screen displayed depending on the specifications of the vehicle.

E181610E04
E181611E04
E181621E02

DIAGNOSIS SYSTEM (WITH MULTI-INFORMATION DISPLAY)
E128079E03

HINT:
  1. The multi-information display shows "DIAG" when the ignition switch is turned on (IG) (Click here).
  2. Diagnosis information can be displayed on the multi-information display after connecting a jumper wire between terminals TC and CG of the DLC3 connector.

← SYSTEM DESCRIPTION (Oct 2006 – May 2009)HOW TO PROCEED WITH TROUBLESHOOTING (Jun 2006 – Sep 2006) →