2006-2011 Camry Aurion · Service Manual TRANSMISSION

TERMINALS OF ECU

System information · Vehicles built from Oct 2006


TCM
C133222E01

HINT:
Each TCM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Symbols (Terminals No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the TCM terminals.

Symbols (Terminals No.)
Wiring Color
Terminal Description
Condition
Specified Condition
R (C56-15) - E1 (C56-8)
W - B-W
R shift position switch signal
Ignition switch on (IG) and shift lever in R position
10 to 14 V
Ignition switch on (IG) and shift lever in any position except R position
Below 1 V
D (C56-16) - E1 (C56-8)
R - B-W
D shift position switch signal
Ignition switch on (IG) and shift lever in D or 3 position
10 to 14 V
Ignition switch on (IG) and shift lever in any position except D and 3 position
Below 1 V
STP (C56-12) - E1 (C56-8)
B - B-W
Stop light switch signal
Brake pedal is depressed
7.5 to 14 V
Brake pedal is released
Below 1.5 V
NSW (C56-11) - E1 (C56-8)
L - B-W
Park/neutral switch signal
Ignition switch on (IG) and shift lever in P or N position
Below 2 V
Ignition switch on (IG) and shift lever in any position except P or N position
Below 1 V
STA (C56-10) - E1 (C56-8)
Y - B-W
Starter signal
Cranking (shift lever position in P or N position, Engine switch START)
10 to 14 V
Ignition switch on (IG) and shift lever in any position except P or N position
Below 2 V
SPD1 (C56-3) - E1 (C56-8)
BR - B-W
Speed signal from combination meter
Vehicle speed 12 mph (20 km/h)
Pulse generation
(See waveform 1)
BATT (C56-1) - E1 (C56-8)
W-L - B-W
Battery (for measuring battery voltage and for TCM memory)
Always
9 to 14 V
IG2 (C56-13) - E1 (C56-8)
L-B - B-W
Ignition switch
Ignition switch on (IG)
9 to 14 V
+B (C56-18) - E1 (C56-8)
W - B-W
Power source of TCM
Ignition switch on (IG)
9 to 14 V
CAN+ (C56-6) - E1 (C56-8)
B - B-W
CAN communication line
Ignition switch on (IG)
Pulse generation
(See waveform 2)
CAN- (C56-7) - E1 (C56-8)
Y - B-W
CAN communication line
Ignition switch on (IG)
Pulse generation
(See waveform 3)

  1. G034872E02
    Waveform 1
    Reference: 
    Terminal
    SPD1 - E1
    Tool setting
    2 V/DIV., 20 ms./DIV.
    Vehicle condition
    Vehicle speed 12 mph (20 km/h)

  2. G036660E07
    Waveform 2
    Reference: 
    Terminal
    CAN+ - E1
    Tool setting
    1 V/DIV., 10 ms./DIV.
    Vehicle condition
    Engine is stopped, ignition switch on (IG)

  3. G036661E06
    Waveform 3
    Reference: 
    Terminal
    CAN- - E1
    Tool setting
    1 V/DIV., 10 ms./DIV.
    Vehicle condition
    Engine is stopped, ignition switch on (IG)


ECM

HINT:
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Symbols (Terminals No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration below as a reference for the ECM terminals.

A107881E43
RHD: 
Symbols (Terminals No.)
Wiring Color
Terminal Description
Condition
Specified Condition
S (A24-25) - E1 (C58-81)
Y - W-B
S shift position switch signal
Ignition switch on (IG) and shift lever in S position
10 to 14 V
Ignition switch on (IG) and shift lever in any position except S position
Below 1 V
SFTU (A24-16) - E1 (C58-81)
R - W-B
Up shift switch signal
Ignition switch on (IG) and shift lever in S position
10 to 14 V
Ignition switch on (IG) and shift lever in "+" position (Up shift)
Below 1 V
SFTD (A24-51) - E1 (C58-81)
L - W-B
Down shift switch signal
Ignition switch on (IG) and shift lever in S position
10 to 14 V
Ignition switch on (IG) and shift lever in "-" position (Down shift)
Below 1 V
LHD: 
Symbols (Terminals No.)
Wiring Color
Terminal Description
Condition
Specified Condition
S (A55-25) - E1 (C55-81)
Y - W-B
S shift position switch signal
Ignition switch on (IG) and shift lever in S position
10 to 14 V
Ignition switch on (IG) and shift lever in any position except S position
Below 1 V
SFTU (A55-16) - E1 (C55-81)
R - W-B
Up shift switch signal
Ignition switch on (IG) and shift lever in S position
10 to 14 V
Ignition switch on (IG) and shift lever in "+" position (Up shift)
Below 1 V
SFTD (A55-51) - E1 (C55-81)
L - W-B
Down shift switch signal
Ignition switch on (IG) and shift lever in S position
10 to 14 V
Ignition switch on (IG) and shift lever in "-" position (Down shift)
Below 1 V
← PROBLEM SYMPTOMS TABLE (from Jun 2009)DIAGNOSIS SYSTEM (Oct 2006 – May 2009) →