INSTALLATION
Removal / installation · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1.
INSTALL BRAKE ACTUATOR WITH BRAKE ACTUATOR BRACKET ASSEMBLY |
 |
- Install the brake actuator with brake actuator bracket assembly to the body with the 3 bolts.
-
Torque:
- 19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
- NOTICE:
- Do not damage the brake lines or wire harness.
- Temporarily tighten each brake line to the correct positions of the brake actuator with brake actuator bracket assembly as shown in the illustration.
- HINT:
- *1: To Front Wheel Cylinder RH
- *2: To Front Wheel Cylinder LH
- *3: To Rear Wheel Cylinder RH
- *4: To Rear Wheel Cylinder LH
- *5: From 2nd Master Cylinder
- *6: From 1st Master Cylinder
- Using SST, fully tighten each brake line.
- SST
- 09023-00101
09023-38201
-
Torque:
- Bolt A M10 without SST:
- 15 N*m{
155 kgf*cm
, 11 ft.*lbf
}
- Bolt A M10 with SST:
- 14 N*m{
143 kgf*cm
, 10 ft.*lbf
}
- Bolt B M12 without SST:
- 19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
- Bolt B M12 with SST:
- 17 N*m{
173 kgf*cm
, 13 ft.*lbf
}
- NOTICE:
- Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
- This torque value is effective when SST is parallel to a torque wrench.
- Connect the actuator connector.
- NOTICE:
- Make sure that the connector is locked securely.
| 2.
INSTALL RADIATOR RESERVE TANK ASSEMBLY |
 |
- Install the radiator reserve tank assembly.
- Connect the radiator reserve tank hose.
| 3.
FILL RESERVOIR WITH BRAKE FLUID
|
 |
- Fill the reservoir with brake fluid.
- Fluid:
- SAE J1703 or FMVSS No. 116 DOT3
| 4.
BLEED BRAKE LINE
|
 |
- NOTICE:
- Bleed the air from the brake line of the wheel farthest from the master cylinder.
- Connect a vinyl tube to the bleeder plug.
Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (*3).
- When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*4).
Repeat (*3) and (*4) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
-
Torque:
- for LHD:
- 8.3 N*m{
85 kgf*cm
, 73 in.*lbf
}
- for RHD:
- 12 N*m{
122 kgf*cm
, 9 ft.*lbf
}
Repeat the above procedures for each wheel to bleed the air from the brake line.
| 5.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
|
| 6.
INSPECT BRAKE FLUID LEVEL
|
 |
- HINT:
- If fluid leaks, tighten or replace the leaking part.
| 7.
INSPECT FOR FLUID LEAK |
|
| 8.
INSPECT ACTUATOR WITH INTELLIGENT TESTER |
 |
- HINT:
- (Click here)
| 9.
INSPECT SENSOR SIGNAL |
 |
- HINT:
- (Click here)
| 10.
CHECK FOR DTC AND CLEAR |
 |
- HINT:
- (Click here)