2006-2011 Camry Aurion · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Using a 6 mm socket hexagon wrench, remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 499 kgf*cm , 36 ft.*lbf }


2. REMOVE FRONT WHEEL

3. REMOVE FRONT AXLE HUB NUT LH

  1. C108168E02
    Using SST and a hammer, release the staked part of the front axle hub nut.
    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the thread of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.


4. REMOVE FRONT AXLE HUB NUT RH

HINT:
Use the same procedures as described for the LH side.


5. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

  1. C140591
    Remove the nut and separate the front stabilizer link assembly.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.


6. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures as described for the LH side.


7. SEPARATE FRONT SPEED SENSOR LH

  1. C140592
    Remove the bolt and clip, and separate the speed sensor wire and flexible hose from the shock absorber.

  1. C132782E01
    Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.


8. SEPARATE FRONT SPEED SENSOR RH

HINT:
Use the same procedures as described for the LH side.


9. SEPARATE TIE ROD ASSEMBLY LH

  1. C108515E05
    Remove the cotter pin and nut.

  1. Using SST, separate the tie rod end sub-assembly from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Make sure that the string of SST is securely tied to the vehicle.
    2. Be careful not to damage the ball joint dust cover.
    3. Be careful not to damage the steering knuckle.
    4. Be careful not to damage the front disc brake dust cover.


10. SEPARATE TIE ROD ASSEMBLY RH

HINT:
Use the same procedures as described for the LH side.


11. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM LH

  1. F040142E01
    Remove the bolt and 2 nuts, and separate the front suspension lower No. 1 arm from the lower ball joint.


12. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:
Use the same procedures as described for the LH side.


13. SEPARATE FRONT AXLE ASSEMBLY LH

  1. D032030E06
    Put matchmarks on the front drive shaft assembly and the axle hub.

  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.


14. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedures as described for the LH side.


15. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

  1. C083850E02
    Using SST, remove the front drive shaft assembly LH.
    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the drive shaft dust cover, boot, and oil seal.
    2. Be careful not to drop the drive shaft assembly.


16. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

  1. C080304E03
    Using a screwdriver, remove the bearing bracket hole snap ring.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

    NOTICE:
    Do not damage the boot and oil seal.


17. SECURE FRONT AXLE ASSEMBLY LH

  1. C054583E02
    Secure the front axle hub bearing.
    SST
    09608-16042   (09608-02021, 09608-02041)

    NOTICE:
    The hub bearing may be damaged if it is subjected to the vehicle's full weight, such as moving the vehicle with the drive shaft removed. If it is necessary to place the vehicle's weight on the hub bearing, first support it with SST.


18. SECURE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedures as described for the LH side.


19. REMOVE TRANSAXLE HOUSING OIL SEAL

  1. C083057E01
    Using SST, pull out the oil seal.
    SST
    09308-00010  


20. REMOVE DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL

  1. C083058E01
    Using SST, pull out the oil seal.
    SST
    09308-00010  

← REMOVAL (Jun 2006 – Sep 2006)REMOVAL (from Jun 2009) →