2006-2011 Camry Aurion · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL KNOCK SENSOR

  1. A128924E01
    Install the knock sensor with the nut.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Make sure that the knock sensor is in the correct position.

  1. Connect the knock sensor connector.


2. INSTALL INTAKE MANIFOLD

  1. A090130E02
    Install a new gasket into the intake manifold.

  1. A135672
    Install the intake manifold with the 5 bolts and 2 nuts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Fit the union to check valve hose into the vacuum hose clamp.

  1. Install the wire harness clamp.

  1. Connect the camshaft timing oil control valve connector.

  1. Connect the union to check valve hose to the brake booster.


3. CONNECT FUEL TUBE

  1. A136017E01
    Install the fuel tube to the fuel hose clamp.

  1. A103968E03
    Push the fuel tube connector until it makes a "click" sound.

  1. A136015E01
    Install the No. 1 fuel pipe clamp.


4. INSTALL FUEL DELIVERY PIPE WITH INJECTOR

  1. A147098
    Install 4 new insulators into the cylinder head.

  1. Install the 2 delivery pipe spacers onto the cylinder head.

  1. A097444E02
    Install the fuel delivery pipe together with the 4 fuel injectors, then temporarily tighten the 2 bolts.

    NOTICE:
    Be careful not to drop the fuel injectors when installing the fuel delivery pipe.

  1. Check that the fuel injector rotates smoothly.
    If the fuel injector does not rotate smoothly, replace the O-ring.

  1. A147099
    Tighten the 2 bolts to the specified torque.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A147100
    Connect the 4 fuel injector connectors.

  1. Install the 2 wire harness clamps.


5. INSTALL THROTTLE BODY

  1. A124566
    Install a new gasket onto the intake manifold.

  1. A128921E01
    Connect the purge line hose to the throttle body.

  1. Connect the water by-pass hose to the throttle body.

  1. Connect the No. 2 water by-pass hose to the throttle body.

  1. Connect the No. 1 throttle body hose to the throttle body.

  1. A128920E01
    Install the throttle body and fuel pipe clamp with the 4 bolts.

    Torque:
    30 N*m{ 305 kgf*cm , 22 ft.*lbf }

  1. Connect the fuel tube into the clamp.

  1. A128919E01
    Connect the throttle position sensor connector.

  1. Connect the wire harness clamp.


6. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  1. A134905
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose clamp.


7. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element onto the air cleaner case.

  1. A135670
    Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.

  1. A236553E01
    Connect the No. 1 air cleaner hose to the throttle body and unfasten the No. 1 air cleaner hose clamp.

    NOTICE:
    1. Match each concave area concavity of the air cleaner hose with the bolt of the throttle body.
    2. Make sure that the hose clamp is at the correct angle.

  1. A146036
    Connect the No. 2 ventilation hose to the air cleaner hose.

  1. A135666E02
    Connect the purge line hose to the clamp (*1).

  1. Connect the 2 purge VSV vacuum hoses (*2).

  1. Connect the purge VSV connector (*3).

  1. Connect the mass air flow meter connector (*4).


8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

9. ADD ENGINE COOLANT
  1. Close the radiator drain cock plug and cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    6.7 liters (7.1 US qts, 5.9 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


10. INSPECT FOR COOLANT LEAK

NOTICE:
Before performing each inspection, turn the A/C switch OFF.

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A135234
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


11. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to the ON position and push the intelligent tester main switch on.

      NOTICE:
      Do not start the engine.

    3. Select the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump /Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sound of fuel flowing in the fuel tank can be heard. If no sound can be heard, check the engine room J/B (C/OPN relay), fuel pump, ECM and wiring connector.

  1. Check for fuel leaks.

    1. Check that there are no fuel leaks anywhere on the system after performing maintenance. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the ignition switch off.

  1. Disconnect the intelligent tester from the DLC3.


12. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A134904
    Install the engine cover with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


13. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

  1. C141972E01
    Install the outer cowl top panel sub-assembly with the 4 bolts and 4 nuts.

    Torque:
    Bolt:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Nut:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }


14. INSTALL WINDSHIELD WIPER MOTOR AND LINK

  1. E135590E01
    Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration.

  1. E135589
    Connect the connector.


15. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E135588
    Engage the 4 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.


16. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

  1. E128810
    Engage the claw and install the front fender to cowl side seal RH.


17. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

  1. E128809
    Engage the claw and install the front fender to cowl side seal LH.


18. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. E112237E01
    Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E128820E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    37 to 52 mm (1.46 to 2.05 in.)


19. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. E112237E01
    Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.

  1. E128821E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    23 to 38 mm (0.90 to 1.49 in.)

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

← INSPECTION (from Jun 2006)INSTALLATION (Oct 2006 – May 2009) →