REASSEMBLY
Removal / installation · Vehicles built from Jun 2006
| 1. INSTALL FRONT DIFFERENTIAL SIDE GEAR |
Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF and install them to the differential case.

| 2. INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT |
Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.

| 3. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN |
Using a pin punch and hammer, install the pinion shaft straight pin.

Using a chisel and hammer, stake the differential case.

- NOTICE:
- Stake it after adjusting the backlash.
| 4. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
Using SST and a press, install the front differential case front tapered roller bearing to the differential case.

- SST
- 09710-30012
(09710-04081)
09550-60010 (09951-00480)
09950-70010 (09951-07100)
- NOTICE:
- Do not damage the bearing cage during installation of the bearing inner race.
Using SST and a hammer, install the front differential case front tapered roller bearing outer race to the transaxle housing.

- SST
- 09950-60020
(09951-00750)
09950-70010 (09951-07200)
| 5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
Using SST and a press, install the front differential case rear tapered roller bearing to the differential case.

- SST
- 09710-30012
(09710-04081)
09550-60010 (09951-00480)
09950-70010 (09951-07100)
- NOTICE:
- Do not damage the bearing cage during installation of the bearing inner race.
Using SST and a hammer, install the front differential case rear tapered roller bearing outer race to the transaxle housing.

- SST
- 09550-60010
(09951-00790)
09950-70010 (09951-00710)
- NOTICE:
- Clearance is not allowed between the bearing and transaxle housing.
| 6. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD |
Install the differential assembly to the transaxle case.

Clean the matching surfaces of the transaxle case and transaxle housing.

Install the transaxle housing to the transaxle case and tighten them with the 18 bolts.
- Torque:
- Bolt A:
- 22 N*m{ 225 kgf*cm , 16 ft.*lbf }
- Bolt B,C:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
- Bolt D:
- 10 N*m{ 101 kgf*cm , 7 ft.*lbf }
- Bolt length:
- Bolt A,B,D:
- 50 mm (1.969 in.)
- Bolt C:
- 42 mm (1.654 in.)
Using SST, turn the differential assembly right and left 2 or 3 times to settle the bearing.

- SST
- 09564-32011
Using SST and a torque wrench, measure the turning torque of the differential.
- SST
- 09564-32011
- Turning torque at 60 rpm:
- New bearing:
- 0.20 to 0.69 N*m (2.0 to 7.0 kgf*cm, 1.8 to 6.1 in.*lbf)
- Used bearing:
- 0.10 to 0.35 N*m (1.0 to 3.6 kgf*cm, 0.9 to 3.1 in.*lbf)
- HINT:
- If the turning torque is not within the specified range, refer to the table below to select a thrust washer so that the turning torque is within the specified range.
Flange thickness: mm (in.) Mark
Thickness
Mark
Thickness
0
1.90 (0.0748)
A
2.40 (0.0945)
1
1.95 (0.0768)
B
2.45 (0.0965)
2
2.00 (0.0787)
C
2.50 (0.0984)
3
2.05 (0.0807)
D
2.55 (0.1004)
4
2.10 (0.0827)
E
2.60 (0.1024)
5
2.15 (0.0846)
F
2.65 (0.1043)
6
2.20 (0.0866)
G
2.70 (0.1063)
7
2.25 (0.0886)
H
2.75 (0.1083)
8
2.30 (0.0906)
J
2.80 (0.1102)
9
2.35 (0.0925)
-
-
Remove the 18 bolts and the transaxle housing.

Remove the differential assembly.

| 7. INSTALL FRONT DIFFERENTIAL RING GEAR |
Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).

- NOTICE:
- Do not overheat the ring gear over 110°C (230.0°F).
Clean the contact surface of the front differential case.
Align the matchmarks, and install the front differential ring gear case quickly.

- NOTICE:
- Do not install the bolts while the ring gear is hot.
Tighten the 10 bolts.

- Torque:
- 95 N*m{ 970 kgf*cm , 70 ft.*lbf }
- NOTICE:
- Tighten the bolts a little at a time in a diagonal pattern.
| 8. INSTALL TRANSAXLE HOUSING OIL SEAL |
Using SST and a hammer, install a new oil seal.

- SST
- 09608-32010
09950-70010 (09951-07150)
Coat the lip of the oil seal with a small amount of MP grease.
- Oil seal installation depth:
- -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
| 9. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL |
Using SST and a hammer, install a new oil seal.

- SST
- 09726-36010
09950-70010 (09951-07150)
Coat the lip of the oil seal with a small amount of MP grease.
- Oil seal installation depth:
- -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
