2006-2011 Camry Aurion · Service Manual STEERING

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL VANE PUMP ASSEMBLY

  1. C135233
    Temporarily install the 2 bolts to the vane pump assembly.

  1. Install the vane pump assembly.

  1. C135229E01
    Using SST, tighten the 2 bolts.
    SST
    09249-63010  

    Torque:
    Without SST:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }
    With SST:
    29 N*m{ 294 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is accurate when SST is parallel to the torque wrench.


2. CONNECT POWER STEERING FLUID PRESSURE SWITCH CONNECTOR

  1. C135234
    Connect the connector to the power steering fluid pressure switch.


3. CONNECT PRESSURE FEED TUBE ASSEMBLY (for LHD)
  1. Install a new gasket to the pressure feed tube assembly.

  1. C135227
    Connect the pressure feed tube assembly to the vane pump assembly with the union bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

    NOTICE:
    Make sure that the stopper of the pressure feed tube assembly contacts the vane pump assembly securely as shown in the illustration.


4. CONNECT PRESSURE FEED TUBE ASSEMBLY (for RHD)
  1. Install a new gasket to the pressure feed tube assembly.

  1. C137703
    Connect the pressure feed tube assembly to the vane pump assembly with the union bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

    NOTICE:
    Make sure that the stopper of the pressure feed tube assembly contacts the vane pump assembly securely as shown in the illustration.


5. CONNECT NO. 1 FLUID RESERVOIR TO PUMP HOSE

  1. C135225E01
    Connect the No. 1 fluid reservoir to pump hose to the vane pump assembly with the clip.

    NOTICE:
    1. Connect the No. 1 fluid reservoir to pump hose with the paint mark facing toward the rear of the vehicle.
    2. Push the No. 1 fluid reservoir to pump hose as far as it will go as shown in the illustration.
    3. Install the clip at the position specified in the illustration.


6. INSTALL V-RIBBED BELT

  1. A114351E03
    Using SST and a 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then install the V-ribbed belt.
    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply more force than necessary.

  1. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Check to confirm that the belt has not slipped out of the grooves on the bottom of the crank pulley by hand.


7. INSTALL FRONT FENDER APRON SEAL RH

8. INSTALL ENGINE UNDER COVER RH

9. ADD POWER STEERING FLUID

10. BLEED POWER STEERING FLUID
  1. Check the fluid level (Click here).

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the steering wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the steering wheel to the left or right to the full lock position and keep it in that position for 2 to 3 seconds, then turn the steering wheel to the opposite full lock position and keep it there for 2 to 3 seconds.

    2. Repeat this procedure several times.

  1. Stop the engine.

  1. C137876E01
    Check for foaming or emulsification.

    HINT:
    If the system has to be bled twice because of forming or emulsification, be sure to check for fluid leaks in the system.

  1. Check the fluid level (Click here).


11. CHECK POWER STEERING FLUID LEVEL
  1. Keep the vehicle level.

  1. C133502E01
    With the engine stopped, check the fluid level in the fluid reservoir.
    If necessary, add fluid.

    Fluid:
    ATF DEXRON II or III, or equivalent

    HINT:
    If the fluid is hot, check that the fluid level is within the HOT range on the fluid reservoir. If the fluid is cold, check that the fluid level is within the COLD range.

  1. Start the engine and run it at idle.

  1. Turn the steering wheel from lock to lock several times to raise fluid temperature.

    Fluid temperature:
    75°C (167°F) to 80°C (176°F)

  1. C137876E01
    Check for foaming or emulsification.
    If foaming or emulsification is identified, bleed the power steering system (Click here).

  1. C137875E01
    With the engine idling, measure the fluid level in the fluid reservoir.

  1. Stop the engine.

  1. Wait a few minutes and remeasure the fluid level in the fluid reservoir.

    Maximum fluid level rise:
    5 mm (0.20 in.)

    If a problem is found, bleed the power steering system (Click here).

  1. Check the fluid level.


12. INSPECT FOR FLUID LEAK

13. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }

← INSTALLATION (Jun 2006 – Sep 2006)INSTALLATION (from Jun 2009) →