2006-2011 Camry Aurion · Service Manual STEERING

REASSEMBLY

Removal / installation · Vehicles built from Jun 2006

NOTICE:
When installing parts, coat the parts indicated by arrows with power steering fluid (Click here).


1. INSTALL VANE PUMP HOUSING OIL SEAL
  1. Coat a new vane pump housing oil seal lip with power steering fluid.

  1. C114702E01
    Using SST and a press, install the vane pump housing oil seal until it is flush with the vane pump front housing end surface.
    SST
    09950-60010   (09951-00280)
    09950-70010   (09951-07100)

    NOTICE:
    Make sure that the oil seal is installed facing in the correct direction as shown in the illustration.


2. INSTALL VANE PUMP SHAFT WITH PULLEY

  1. C114703E01
    Coat the inside surface of the bushing in the vane pump front housing with power steering fluid.

  1. Gradually insert the vane pump shaft with pulley.

    NOTICE:
    Do not damage the oil seal lip in the front housing.

    HINT:
    Wrap protective tape around the spline of the vane pump shaft with pulley in order to prevent damage to the oil seal.


3. INSTALL VANE PUMP FRONT SIDE PLATE

  1. C132035
    Coat a new O-ring with power steering fluid and install it into the vane pump front housing.

  1. C107035
    Coat a new O-ring with power steering fluid and install it onto the vane pump front side plate.

  1. C132040E01
    Align the notch of the vane pump front side plate with that of the vane pump front housing, and install the vane pump front side plate.

    NOTICE:
    Make sure that the vane pump front side plate is installed facing in the correct direction.


4. INSTALL VANE PUMP CAM RING

  1. C139139E01
    Align the notch of the cam ring with that of the vane pump front side plate, and install the vane pump cam ring with the inscribed mark facing upward.

    NOTICE:
    Make sure that the vane pump cam ring is installed facing in the correct direction.


5. INSTALL VANE PUMP ROTOR

  1. C107038
    Install the vane pump rotor.

    HINT:
    The vane pump rotor can be installed in both directions.

  1. Coat the 10 vane pump plates with power steering fluid.

  1. C141370E01
    Install the vane pump plates with the round end facing outward.

    NOTICE:
    Make sure that the vane pump plates are installed facing in the correct direction.


6. INSTALL VANE PUMP SHAFT SNAP RING

  1. D030336E01
    Using a screwdriver and a snap ring expander, install a new vane pump shaft snap ring onto the vane pump shaft with pulley.

    NOTICE:
    Make sure that the vane pump shaft snap ring is securely installed in the vane pump shaft groove.


7. INSTALL VANE PUMP REAR HOUSING

  1. C107040
    Coat a new O-ring with power steering fluid and install it onto the vane pump rear housing.

  1. C136780E01
    Align the straight pin of the vane pump rear housing with the notches of the vane pump cam ring, vane pump front side plate, and vane pump front housing.

  1. C107024
    Install the vane pump rear housing with the 4 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }


8. INSPECT TOTAL PRELOAD

  1. C053369E10
    Check that the pump rotates smoothly without abnormal noise.

  1. Temporarily install the service bolt.

    Recommended service bolt:
    Thread diameter:
    10 mm (0.39 in.)
    Thread pitch:
    1.25 mm (0.0492 in.)
    Bolt length:
    50 mm (1.97 in.)

  1. Using a torque wrench, check the pump rotating torque.

    Rotating torque:
    0.27 N*m (2.8 kgf*cm, 2.4 in.*lbf) or less

    If the rotating torque is not as specified, check the vane pump housing oil seal.


9. INSTALL FLOW CONTROL VALVE ASSEMBLY

  1. C132033
    Coat the flow control valve assembly with power steering fluid.

  1. Install the flow control valve compression spring and the flow control valve assembly to the vane pump front housing.

  1. Coat a new O-ring with power steering fluid and install it onto the pressure port union.

  1. Install the pressure port union to the vane pump front housing.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf }


10. INSTALL POWER STEERING FLUID PRESSURE SWITCH
  1. Coat the new O-ring attached to the new power steering fluid pressure switch with power steering fluid.

  1. C133180
    Install the power steering fluid pressure switch to the vane pump assembly.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

    NOTICE:
    Do not use a power steering fluid pressure switch that has been subjected to an impact; for example, due to it having been dropped.


11. INSTALL POWER STEERING SUCTION PORT UNION
  1. Coat a new O-ring with power steering fluid and install it to the power steering suction port union.

  1. C135231
    Install the power steering suction port union to the vane pump assembly with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

← INSPECTION (from Jun 2006)INSTALLATION (Jun 2006 – Sep 2006) →