Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM (for 2AZ-FE)
Headlight (HI-BEAM) Circuit
Circuit diagnosis · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – May 2009 from Jun 2009
DESCRIPTION
When the low beam headlights are on, and the dimmer switch is turned to the HIGH position, the main body ECU turns the high beam headlights on.
HINT:
When a short circuit occurs between the power distributor and high beam headlight, the power distributor stops the high beam headlight relay operation (Fail-safe function).
The high beam headlight relay is built into the power distributor, so unlike conventional relays, it cannot be removed for inspection.
WIRING DIAGRAM
INSPECTION PROCEDURE
1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Select the item below in the ACTIVE TEST and then check that the relay operates.
Main Body (Main Body ECU):
Tester Display
Test Part
Control Range
Diagnostic Note
Headlight (HI)
High beam headlights
ON / OFF
-
OK:
High beam headlight relay operates. (High beam headlights illuminate.)
OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG
2. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Condition
Specified Condition
ID-3 (HRLY) - Body ground
Light control switch OFF → HEAD
10 to 14 V → Below 1 V
ID-9 (DIM) - Body ground
Light control switch in HEAD and dimmer switch LOW → HIGH
10 to 14 V → Below 1 V
OK
NG
3. CHECK HARNESS AND CONNECTOR (ENGINE ROOM J/B ASSEMBLY - BATTERY AND BODY GROUND)
Disconnect the 1G engine room J/B assembly connector.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Condition
Specified Condition
1G-1 - Body ground
Always
10 to 14 V
Disconnect the 1E engine room J/B assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
1E-11 - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
4. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY
Reconnect the 1G and 1E engine room J/B assembly connectors.
Disconnect the 1D engine room J/B assembly connector.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Condition
Specified Condition
1D-8 - Body ground
Always
10 to 14 V
1D-9 - Body ground
Always
10 to 14 V
NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (POWER DISTRIBUTOR)
OK
5. CHECK HARNESS AND CONNECTOR (ENGINE ROOM J/B ASSEMBLY - INSTRUMENT PANEL J/B ASSEMBLY)
Reconnect the 1D engine room J/B assembly connector.
Disconnect the ID instrument panel J/B connector.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Condition
Specified Condition
ID-3 (HRLY) - Body ground
Always
10 to 14 V
ID-9 (DIM) - Body ground
Always
10 to 14 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
6. CHECK HARNESS AND CONNECTOR (SHORT IN RELAY-DRIVEN CIRCUIT)
Remove the H-LP (RH) fuse from the engine room J/B assembly.
Turn the light control switch to the HEAD position.
Turn the dimmer switch to the HIGH position.
Check if the high beam headlight LH illuminates.
Turn the dimmer switch to the LOW position.
Install the H-LP (RH) fuse and remove the H-LP (LH) fuse.
Turn the dimmer switch to the HIGH position.
Check if the high beam headlight RH illuminates.
OK:
Either high beam headlight LH or RH illuminates.
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (SHORT CIRCUIT BETWEEN FUSE AND BULB)
NG
7. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY
Remove the H-LP (RH) fuse and H-LP (LH) fuse from the engine room J/B assembly.
Measure the voltage between the loading slot of each fuse and body ground.
Standard voltage:
Tester Connection
Condition
Specified Condition
H-LP (RH) Terminal - Body ground
Light control switch in HEAD and dimmer switch in HIGH
10 to 14 V
H-LP (LH) Terminal - Body ground
Light control switch in HEAD and dimmer switch in HIGH
10 to 14 V
NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (POWER DISTRIBUTOR)
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (OPEN CIRCUIT BETWEEN FUSE AND BODY GROUND)