2006-2011 Camry Aurion · Service Manual ENGINE

ADJUSTMENT

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. REMOVE FRONT WHEEL RH

2. REMOVE ENGINE UNDER COVER LH

3. REMOVE ENGINE UNDER COVER RH

4. REMOVE FRONT FENDER APRON SEAL RH

5. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A134904
    Remove the 2 nuts and cover.


6. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 4 bolts and 4 ignition coils.


7. DISCONNECT VENTILATION HOSE

8. DISCONNECT NO. 2 VENTILATION HOSE

9. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A112210E01
    Remove the 2 bolts and disconnect the 2 engine wires.

  1. A127550E02
    Remove the 8 bolts, 2 nuts and cylinder head cover.


10. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A098345E09
    Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.

  1. Check that each timing mark of the camshaft timing gear and sprocket is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as above.

    NOTICE:
    Make sure that the timing mark of the No.2 bearing cap is aligned with the timing mark as the Type B camshaft sprocket has several other marks.


    A361177E01


11. CHECK VALVE CLEARANCE

  1. A098170E04
    Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (cold):
      Item
      Standard Condition
      Intake
      0.19 to 0.29 mm (0.0075 to 0.0114 in.)
      Exhaust
      0.30 to 0.40 mm (0.0118 to 0.0157 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.

  1. Turn the crankshaft 1 revolution (360°) and set the No. 4 cylinder to TDC/compression.

  1. A098171E04
    Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard valve clearance (cold):
      Item
      Standard Condition
      Intake
      0.19 to 0.29 mm (0.0075 to 0.0114 in.)
      Exhaust
      0.30 to 0.40 mm (0.0118 to 0.0157 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.


12. ADJUST VALVE CLEARANCE
  1. Remove the No. 2 camshaft (Click here).

  1. Remove the camshaft (Click here).

  1. Remove the valve lifters.

  1. A001082E01
    Using a micrometer, measure the thickness of the removed valve lifters.

  1. Calculate the thickness of a new lifter so that the valve clearance comes within the specified values.

    New lifter thickness:
    Item
    Specification
    Intake
    A = B + (C - 0.24 mm (0.0095 in.))
    Exhaust
    A = B + (C - 0.35 mm (0.0138 in.))

    A
    New lifter thickness
    B
    Used lifter thickness
    C
    Measured valve clearance
    CALCULATION EXAMPLE (Intake):
    1. Measured intake valve clearance = 0.40 mm (0.0158 in.)
      (Measured - Specification = Excess clearance)
      1. 0.40 mm (0.0158 in.) - 0.24 mm (0.0095 in.) = 0.16 mm (0.0063 in.)
    2. Measured used lifter thickness = 5.250 mm (0.2067 in.)
    3. New lifter thickness = 5.410 mm (0.2130 in.)
      (Excess clearance + Used lifter thickness = Ideal new lifter)
      1. 0.16 mm (0.0063 in.) + 5.250 mm (0.2067 in.) = 5.410 mm (0.2130 in.)
    4. Closest new lifter = 5.420 mm (0.2134 in.)
      1. Select No. 42 lifter

  1. A126901E01
    Select a new lifter with a thickness as close as possible to the calculated values.

    HINT:
    1. Lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 to 5.740 mm (0.1992 to 0.2260 in.).
    2. The identification number inside the valve lifters shows the value to 2 decimal places. (The illustration shows 5.420 mm (0.2134 in.))

  1. Valve lifter selection chart (intake).

    A126931E02

    New lifter thickness 
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700 (0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)
    -
    -

    Standard intake valve clearance (cold):
    0.19 to 0.29 mm (0.0075 to 0.0114 in.)

    EXAMPLE:
    The 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0157 in.). Replace the 5.250 mm (0.2067 in.) lifter with a new No. 42 lifter.

  1. Valve lifter selection chart (exhaust).

    A114356E01

    New lifter thickness 
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    Lifter No.
    Thickness
    mm (in.)
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700 (0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)
    -
    -

    Standard exhaust valve clearance (cold):
    0.30 to 0.40 mm (0.0118 to 0.0157 in.)

    EXAMPLE:
    The 5.340 mm (0.2102 in.) lifter is installed, and the measured clearance is 0.430 mm (0.0169 in.). Replace the 5.340 mm (0.2102 in.) lifter with a new No. 42 lifter.

  1. Install the selected valve lifter.


13. INSTALL CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the camshaft.

  1. A098176E04
    Install the timing chain onto the camshaft timing gear with the paint mark aligned with the timing mark on the camshaft timing gear as shown in the illustration.

  1. A098177E03
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A098177E06
    Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    No. 1 bearing cap:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }
    No. 3 bearing cap:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


14. INSTALL NO. 2 CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the No. 2 camshaft.

  1. A098178E03
    Put the No. 2 camshaft on the cylinder head with the paint mark of the chain aligned with the timing mark on the camshaft timing sprocket.

  1. NOTICE:
    Make sure that the paint mark of the chain is aligned with the timing mark as the Type B camshaft sprocket has several other marks.


    A361177E01

  1. A086659
    While holding the No. 2 camshaft by hand, temporarily tighten the camshaft timing sprocket set bolt.

  1. A098174E05
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A098174E07
    Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    No. 2 bearing cap:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }
    No. 3 bearing cap:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A098173E04
    While holding the camshaft with a wrench, tighten the camshaft timing sprocket set bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    NOTICE:
    Be careful not to damage the valve lifter.

  1. A098180E04
    Check that the paint marks on the chain are aligned with the timing marks on the camshaft timing gear and camshaft timing sprocket. Also, check that the crankshaft pulley groove is aligned with the timing mark "0" of the timing chain cover.

    NOTICE:
    Make sure that the paint mark of the chain is aligned with the timing mark as the Type B camshaft sprocket has several other marks.

  1. A361177E01


15. INSTALL NO. 1 CHAIN TENSIONER

  1. A098376E03
    Release the ratchet pawl, then fully push in the plunger and put the hook to the pin so that the plunger is in the position shown in the illustration.

  1. A098377E03
    Install a new gasket and the chain tensioner with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    If the hook releases the plunger while the chain tensioner is being installed, set the hook again.

  1. A112204E02
    Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.

  1. A112205E02
    Turn the crankshaft clockwise, then check that the plunger is extended.


16. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing material from the contact surfaces.

  1. A094205E01
    Apply seal packing to the 2 locations shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the cylinder head cover within 3 minutes of applying seal packing.
    3. Do not add engine oil for at least 2 hours after installing the cylinder head cover.

  1. A127550E01
    Install the cylinder head cover with the 8 bolts and 2 nuts.

    Torque:
    Bolt A:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    Bolt B:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }
    Nut:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. A112210
    Install the 2 engine wires with the 2 bolts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


17. INSTALL NO. 2 VENTILATION HOSE

18. INSTALL VENTILATION HOSE

19. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 4 ignition coils with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


20. INSPECT FOR ENGINE OIL LEAKS

21. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A134904
    Install the engine cover with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


22. INSTALL FRONT FENDER APRON SEAL RH

23. INSTALL ENGINE UNDER COVER LH

24. INSTALL ENGINE UNDER COVER RH

25. INSTALL FRONT WHEEL RH
← ADJUSTMENT (Oct 2006 – May 2009)COMPONENTS (Jun 2006 – May 2009) →