2006-2011 Camry Aurion · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built Jun 2006 – May 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009


CHECK BATTERY CONDITION

NOTICE:
If the battery is weak or if the engine is difficult to start, perform the following procedures.

  1. Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.

  1. Check the electrolyte quantity of each cell.

    1. For maintenance-free batteries:

      1. If the electrolyte quantity is below the lower line, replace the battery.
      2. If the electrolyte quantity is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery.

      HINT:
      Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).

    2. For non-maintenance-free batteries:

      1. If the electrolyte quantity is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte's specific gravity.

        Standard specific gravity:
        1.25 to 1.29 at 20°C (68°F)

      2. If the electrolyte quantity is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery.

      HINT:
      Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).


CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.
    If the terminals are corroded, clean them.


CHECK FUSES
  1. Measure the resistance of the ALT fuse, ALT-S fuse, GAUGE No. 1 fuse and GAUGE No. 2 fuse.

    Standard resistance:
    Below 1 Ω

    If the result is not as specified, replace the fuses as necessary.


CHECK V-RIBBED BELT

  1. B000543
    Check the belt for wear, cracks or other signs of damage.
    If any of the following defects is found, replace the V-ribbed belt.
    1. The belt is worn out, cracked, or the cords are exposed.
    2. The cracks reach the cords in more than one place.
    3. The belt has chunks missing from the ribs.

  1. B000540E03
    Check that the belt fits properly in the ribbed grooves.

    HINT:
    Check with your hand to confirm that the belt has not slipped out of the groove on the bottom of the pulley.
    If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt correctly.


VISUALLY CHECK GENERATOR WIRING
  1. Check that the generator wiring is in good condition.
    If the condition is not good, repair or replace the generator wire.


LISTEN FOR ABNORMAL NOISES FROM GENERATOR
  1. Check that there is no abnormal noise from the generator while the engine is running.
    If there is abnormal noise, replace the pulley or generator.


CHECK CHARGE WARNING LIGHT CIRCUIT
  1. Turn the ignition switch to the ON position. Check that the charge warning light comes on.

  1. Start the engine and check that the light goes off.
    If the light does not operate as specified, troubleshoot the charge warning light circuit.


CHECK CHARGING CIRCUIT WITHOUT LOAD

  1. A110265E04
    According to the following procedure, connect an ammeter and voltmeter as shown in the illustration.

    1. Disconnect the wire from terminal B of the generator and connect it to the negative (-) lead of the ammeter.

    2. Connect the positive (+) lead of the ammeter to terminal B of the generator.

    3. Connect the positive (+) lead of the voltmeter to positive (+) terminal of the battery.

    4. Ground the negative (-) lead of the voltmeter.

  1. Check the charging circuit.

    1. While keeping the engine speed at 2,000 rpm, check the readings on the ammeter and voltmeter.

      Standard amperage:
      10 A or less

      Standard voltage:
      G.C.C. countries:
      13.0 to 14.6 V
      Australia:
      13.2 to 14.8 V

      If the results are not as specified, replace the generator assembly.

      HINT:
      If the battery is not fully charged, the ammeter reading may be more than the standard amperage.


CHECK CHARGING CIRCUIT WITH LOAD
  1. Keep the engine speed at 2,000 rpm, turn on the high beam headlights, and turn the heater blower switch to the "HI" position.

  1. Check the reading on the ammeter.

    Standard amperage:
    30 A or more

    If the ammeter reading is less than the standard amperage, replace the generator assembly.

    HINT:
    If the battery is fully charged, the ammeter reading may be less than the standard amperage. In this case, increase electrical load by operating devices such as the wiper motor and rear window defogger. Then, recheck the reading on the ammeter.

← PROBLEM SYMPTOMS TABLE (from Jun 2009)ON-VEHICLE INSPECTION (from Jun 2009) →