2006-2011 Camry Aurion · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Seat)

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment (Click here).


2. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 2AZ-FE Manual Seat)

3. REMOVE OUTER SEAT TRACK BRACKET COVER LH (for 2AZ-FE Manual Seat)
  1. Move the front seat assembly fully forward by operating the slide handle.

  1. B149587
    Using a screwdriver, disengage the 4 claws and remove the outer seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


4. REMOVE INNER SEAT TRACK BRACKET COVER LH (for 2AZ-FE Manual Seat)

  1. B149588
    Using a screwdriver, disengage the 4 claws and remove the inner seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


5. REMOVE FRONT SEAT ASSEMBLY LH (for 2AZ-FE Manual Seat)
  1. Move the front seat assembly to the rearmost position by operating the slide handle.

  1. B139101
    Remove the 2 bolts on the front seat track bracket.

  1. Move the front seat assembly fully forward by operating the slide handle.

  1. B139102
    Remove the 2 bolts on the rear seat track bracket.

  1. Move the front seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and reclining adjuster release handle.

  1. Disconnect the connectors and clamp.

  1. Remove the front seat assembly.


6. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 2GR-FE RHD Manual Seat)

7. REMOVE OUTER SEAT TRACK BRACKET COVER LH (for 2GR-FE RHD Manual Seat)
  1. Move the front seat assembly fully forward by operating the slide handle.

  1. B146646
    Using a screwdriver, disengage the 4 claws and remove the outer seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


8. REMOVE INNER SEAT TRACK BRACKET COVER LH (for 2GR-FE RHD Manual Seat)
  1. Using a screwdriver, disengage the 4 claws and remove the inner seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


9. REMOVE FRONT SEAT ASSEMBLY LH (for 2GR-FE RHD Manual Seat)
  1. Move the front seat assembly to the rearmost position by operating the slide handle.

  1. B166772
    Remove the 2 bolts on the front seat track bracket.

  1. Move the front seat assembly fully forward by operating the slide handle.

  1. B146648
    Remove the 2 bolts on the rear seat track bracket.

  1. Move the front seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and reclining adjuster release handle.

  1. Disconnect the connectors and clamp.

  1. Remove the front seat assembly.


10. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 2AZ-FE Power Seat)

11. REMOVE OUTER SEAT TRACK BRACKET COVER LH (for 2AZ-FE Power Seat)
  1. Operate the power seat switch knob and move the seat to the position farthest forward.

  1. B149587
    Using a screwdriver, detach the 4 claws and remove the outer seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


12. REMOVE INNER SEAT TRACK BRACKET COVER LH (for 2AZ-FE Power Seat)

  1. B149588
    Using a screwdriver, detach the 4 claws and remove the inner seat track bracket cover.


13. REMOVE FRONT SEAT ASSEMBLY LH (for 2AZ-FE Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B149590
    Remove the 2 bolts on the front seat track bracket.

  1. Operate the power seat switch knob and move the seat to the position farthest forward.

  1. B139102
    Remove the 2 bolts on the rear seat track bracket.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).

  1. Disconnect the connectors under the seat. Then remove the front seat assembly.


14. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 2GR-FE LHD Power Seat)

15. REMOVE OUTER SEAT TRACK BRACKET COVER LH (for 2GR-FE LHD Power Seat)
  1. Operate the power seat switch knob and move the seat to the position farthest forward.

  1. B149587
    Using a screwdriver, detach the 4 claws and remove the outer seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


16. REMOVE INNER SEAT TRACK BRACKET COVER LH (for 2GR-FE LHD Power Seat)

  1. B149588
    Using a screwdriver, detach the 4 claws and remove the inner seat track bracket cover.


17. REMOVE FRONT SEAT ASSEMBLY LH (for 2GR-FE LHD Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B149590
    Remove the 2 bolts on the front seat track bracket.

  1. Operate the power seat switch knob and move the seat to the position farthest forward.

  1. B139102
    Remove the 2 bolts on the rear seat track bracket.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).

  1. Disconnect the connectors under the seat. Then remove the front seat assembly.


18. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 2GR-FE RHD Power Seat)

19. REMOVE OUTER SEAT TRACK BRACKET COVER LH (for 2GR-FE RHD Power Seat)

HINT:
Use the same procedure for the RH side and LH side.


20. REMOVE INNER SEAT TRACK BRACKET COVER LH (for 2GR-FE RHD Power Seat)

HINT:
Use the same procedure for the RH side and LH side.


21. REMOVE FRONT SEAT ASSEMBLY LH (for 2GR-FE RHD Power Seat)

HINT:
Use the same procedure for the RH side and LH side.


22. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 2AZ-FE Manual Seat)

23. REMOVE OUTER SEAT TRACK BRACKET COVER RH (for 2AZ-FE Manual Seat)

  1. B147665
    Move the front passenger's seat assembly fully forward by operating the slide handle.

  1. Using a screwdriver, disengage the 4 claws and remove the outer seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


24. REMOVE INNER SEAT TRACK BRACKET COVER RH (for 2AZ-FE Manual Seat)

  1. B147666
    Using a screwdriver, disengage the 4 claws and remove the inner seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


25. REMOVE FRONT SEAT ASSEMBLY RH (for 2AZ-FE Manual Seat)
  1. Move the front passenger's seat assembly to the rearmost position by operating the slide handle.

  1. B147667
    Remove the 2 bolts on the front seat track bracket.

  1. Move the front passenger's seat assembly fully forward by operating the slide handle.

  1. B147668
    Remove the 2 bolts on the rear seat track bracket.

  1. Move the front passenger's seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and reclining adjuster release handle.

  1. Disconnect the connectors and clamp.

  1. Remove the front passenger's seat assembly.


26. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 2GR-FE LHD Manual Seat)

27. REMOVE OUTER SEAT TRACK BRACKET COVER RH (for 2GR-FE LHD Manual Seat)
  1. Move the front seat assembly fully forward by operating the slide handle.

  1. B148935
    Using a screwdriver, disengage the 4 claws and remove the outer seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


28. REMOVE INNER SEAT TRACK BRACKET COVER RH (for 2GR-FE LHD Manual Seat)

  1. B148936
    Using a screwdriver, disengage the 4 claws and remove the inner seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


29. REMOVE FRONT SEAT ASSEMBLY RH (for 2GR-FE LHD Manual Seat)
  1. Move the front seat assembly to the rearmost position by operating the slide handle.

  1. B148945
    Remove the 2 bolts on the front seat track bracket.

  1. Move the front seat assembly fully forward by operating the slide handle.

  1. B148937
    Remove the 2 bolts on the rear seat track bracket.

  1. Move the front seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and reclining adjuster release handle.

  1. Disconnect the connectors and clamp.

  1. Remove the front seat assembly.


30. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 2AZ-FE Power Seat)

31. REMOVE OUTER SEAT TRACK BRACKET COVER RH (for 2AZ-FE Power Seat)

HINT:
Use the same procedure for the RH side and LH side.


32. REMOVE INNER SEAT TRACK BRACKET COVER RH (for 2AZ-FE Power Seat)

HINT:
Use the same procedure for the RH side and LH side.


33. REMOVE FRONT SEAT ASSEMBLY RH (for 2AZ-FE Power Seat)

HINT:
Use the same procedure for the RH side and LH side.


34. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 2GR-FE LHD Power Seat)

35. REMOVE OUTER SEAT TRACK BRACKET COVER RH (for 2GR-FE LHD Power Seat)
  1. Move the front passenger's seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. B147681
    Using a screwdriver, disengage the 4 claws and remove the outer seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


36. REMOVE INNER SEAT TRACK BRACKET COVER RH (for 2GR-FE LHD Power Seat)
  1. Using a screwdriver, disengage the 4 claws and remove the inner seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


37. REMOVE FRONT SEAT ASSEMBLY RH (for 2GR-FE LHD Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B153030
    Remove the 2 bolts on the front seat track bracket.

  1. Operate the power seat switch knob and move the seat fully forward.

  1. B153020
    Remove the 2 bolts on the rear seat track bracket.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).

  1. Disconnect the connectors under the seat. Then remove the front passenger's seat assembly.


38. REMOVE FRONT SEAT HEADREST ASSEMBLY (for 2GR-FE RHD Power Seat)

39. REMOVE OUTER SEAT TRACK BRACKET COVER RH (for 2GR-FE RHD Power Seat)
  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. B147681
    Using a screwdriver, disengage the 4 claws and remove the front seat rear outer track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


40. REMOVE INNER SEAT TRACK BRACKET COVER RH (for 2GR-FE RHD Power Seat)
  1. Using a screwdriver, disengage the 4 claws and remove the front seat rear inner track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


41. REMOVE FRONT SEAT ASSEMBLY RH (for 2GR-FE RHD Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B147683
    Remove the 2 bolts on the front seat track bracket.

  1. Operate the power seat switch knob and move the seat to the position farthest forward.

  1. B147684
    Remove the 2 bolts on the rear seat track bracket.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).

  1. Disconnect the connectors under the seat. Then remove the front seat assembly.


42. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)

  1. B136575E01
    Detach the 2 front hooks of the seat cushion from the vehicle body.

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.


43. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

  1. B134699E01
    Detach the 2 front hooks of the seat cushion from the vehicle body.

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the step above for the other hook.

  1. Remove the seat cushion.


44. REMOVE REAR SEAT HEADREST ASSEMBLY

45. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)

46. REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

  1. B136576
    Remove the 3 rear seat belts from the 3 rear seat shoulder belt guides.

  1. B136577
    Remove the 4 bolts and rear seatback assembly.


47. REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

  1. B136539
    Remove the 2 bolts and separate type rear seatback assembly LH.


48. REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

  1. B134700
    Remove the 2 bolts and separate type rear seatback assembly RH.


49. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

  1. B136561
    Remove the bolt and rear side seatback assembly LH.


50. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

HINT:
Use the same procedure for the RH side and LH side.


51. REMOVE REAR DOOR SCUFF PLATE LH

  1. B132068
    Disengage the 5 claws and 2 clips, and remove the rear door scuff plate LH.


52. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

53. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and LH side.


54. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

55. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH

  1. B136443E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.


56. REMOVE DOOR ASSIST GRIP COVER LH

  1. B149028E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the door assist grip cover.


57. REMOVE REAR ASH RECEPTACLE ASSEMBLY LH (w/ Ashtray)

  1. B136442
    Remove the rear ash receptacle assembly.


58. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. B146097E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.

  1. Disconnect the connector.


59. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B136451
    Remove the 3 screws.

  1. Using a clip remover, disengage the 7 clips.

  1. B136452
    Raise the rear door trim board to disengage the 4 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.

  1. Disconnect the connector.

  1. B136453
    Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.

  1. B141704
    Disengage the clip as shown in the illustration and remove the No. 1 door scuff plate clamp from the rear door trim board.


60. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

  1. B136456
    Disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.


61. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132067
    Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.


62. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


63. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

64. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

  1. B131995
    Disengage the 3 claws and remove the lap belt outer anchor cover.


65. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

  1. B131996
    Remove the bolt and disconnect the floor end of the front seat outer belt assembly LH.


66. REMOVE LOWER CENTER PILLAR GARNISH LH

  1. B132057
    Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.


67. REMOVE UPPER CENTER PILLAR GARNISH LH

  1. B132059
    Remove the bolt.

  1. Disengage the clip and remove the upper center pillar garnish LH.


68. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and LH side.


69. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.


70. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

71. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure for the RH side and LH side.


72. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.


73. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and LH side.


74. REMOVE UPPER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and LH side.


75. REMOVE ROOF SIDE INNER GARNISH LH

  1. B132063
    Disengage the 5 clips and 2 claws, and remove the roof side inner garnish LH.


76. REMOVE ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure for the RH side and LH side.


77. REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

  1. B132056E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish LH.

  1. Remove the clip <A> from the vehicle body.


78. REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

  1. B132056E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish LH.

  1. Remove the clip <A> from the vehicle body.

  1. B132100E02
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


79. REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

  1. B132055E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish RH.

  1. Remove the clip <A> from the vehicle body.


80. REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

  1. B132055E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish RH.

  1. Remove the clip <A> from the vehicle body.

  1. B132099E02
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


81. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

  1. E128843
    Remove the rain sensor cover.


82. REMOVE ROOF CONSOLE BOX ASSEMBLY

  1. B132064
    Using a moulding remover, disengage the 2 clips and 2 claws.

  1. Disconnect the connectors and remove the roof console box assembly.


83. REMOVE VISOR ASSEMBLY LH

  1. B132069
    Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.

  1. B132070
    Disengage the 2 clips and remove the visor assembly LH.


84. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.


85. REMOVE VISOR HOLDER
  1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

  1. Disengage the 2 claws and remove the visor holder.

    B132066E01

    HINT:
    Use the same procedure for the RH side and the LH side.


86. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (for Driver Side)

  1. with Assist Grip:

    1. B132061E01
      Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.

      HINT:
      Tape the screwdriver tip before use.

    2. B132062
      Disengage the 2 clips and remove the front assist grip sub-assembly.


87. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (for Front Passenger Side)

  1. B147410E01
    Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.

    HINT:
    Tape the screwdriver tip before use.

  1. B147411
    Disengage the 2 clips and remove the front assist grip sub-assembly.


88. REMOVE REAR ASSIST GRIP SUB-ASSEMBLY

HINT:
Use the same procedure for the rear side and front side.


89. REMOVE SPOT LIGHT ASSEMBLY

  1. B132093E01
    Using a screwdriver, disengage the 2 claws labeled A and 2 claws labeled B from the vehicle body.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a screwdriver, disengage the 2 claws labeled C and remove the spot light assembly from the headlining.

    HINT:
    Tape the screwdriver tip before use.

  1. B132095E01
    Using a screwdriver, disengage the 4 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Pull the light bulb holder in the direction indicated by the arrow in the illustration to detach the claw. Then remove the spot light assembly from the light bulb holder.


90. REMOVE SUN ROOF OPENING TRIM MOULDING
  1. Remove the sun roof opening trim moulding.


91. REMOVE ROOF HEADLINING ASSEMBLY
  1. Disconnect the No. 1 roof wire connector and disengage each clamp from the front pillar LH.

  1. Remove the bolt and disconnect the radio setting condenser from the front pillar RH.

  1. Disconnect the antenna cord sub-assembly connector and disengage each clamp from the front pillar RH.

  1. Disconnect the antenna cord sub-assembly connector and disengage the clamp from the rear pillar RH.

  1. Disconnect the sliding roof drive gear connector.

  1. Disengage the hook, 4 clips, and 2 fasteners.

    B149212E01

  1. B149222
    Remove the roof headlining assembly from the vehicle through the rear left door.


92. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH
  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the 4 clips.

    1. C141263E01
      Using a clip remover, remove the pin.

    2. C141264E03
      Using needle-nose pliers, remove the clip and curtain shield airbag from the body as shown in the illustration.

  1. Remove the 5 bolts and curtain shield airbag assembly.

    C132575

  1. Remove the 4 clips and 4 spacers from the curtain shield airbag assembly.

    NOTICE:
    If clips and spacers are removed, always replace them with new ones even though they may not appear to be damaged.


93. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


94. REMOVE SLIDING ROOF SIDE GARNISH LH

  1. B132108
    Disengage the 6 claws and remove the sliding roof side garnish LH.


95. REMOVE SLIDING ROOF SIDE GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


96. REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY

  1. Using a T25 "TORX" driver, remove the 4 screws and sliding roof glass sub-assembly.

    NOTICE:
    To prevent the sliding roof glass and sliding roof drive gear from being displaced, fully close the sliding roof glass (sliding roof drive cable), and then remove the sliding roof drive gear.


    B148828


97. REMOVE SLIDING ROOF HOUSING SUB-ASSEMBLY
  1. Disconnect the 4 sliding roof drain hoses.

  1. Remove the 4 bolts, 8 nuts, and sliding roof housing sub-assembly.

    B152846


98. REMOVE SLIDING ROOF WEATHERSTRIP
  1. Remove the sliding roof weatherstrip from the sliding roof glass sub-assembly.

← REMOVAL (Oct 2006 – May 2009)DISASSEMBLY (from Jun 2006) →