2006-2011 Camry Aurion · Service Manual HEATER & AIR CONDITIONING SYSTEM

Steering Pad Switch Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

AUTO, OFF, TEMP UP (+), and TEMP DOWN (-) switches are located on the steering pad switch. The resistance of the steering pad switch changes in accordance with switch operation. The A/C control assembly outputs voltage to the steering pad switch and reads voltage changes due to the resistance changes that result from switch operation.

HINT:
If there is an open in the circuit, the A/C system cannot be operated by the steering pad switch assembly.
If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the A/C control assembly cannot be operated by the steering pad switch assembly, and the A/C control assembly will not be able to function correctly.


WIRING DIAGRAM

E124492E17

INSPECTION PROCEDURE


1. INSPECT A/C CONTROL ASSEMBLY

  1. E124479E07
    Remove the A/C control assembly with the connectors still connected.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    F16-9 (ADI1) - F16-8 (SG)
    AUTO switch: ON
    Below 2.5 Ω
    F16-9 (ADI1) - F16-8 (SG)
    OFF switch: ON
    Approx. 329 Ω
    F16-9 (ADI1) - F16-8 (SG)
    TEMP+ switch: ON
    Approx. 1,000 Ω
    F16-9 (ADI1) - F16-8 (SG)
    TEMP- switch: ON
    Approx. 3,110 Ω



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2. INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Remove the steering pad switch assembly.

  1. Disconnect the connector from the steering pad switch assembly.E124484E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    a1-3 (AC1) - a1-2 (EAC)
    AUTO switch: ON
    Below 2.5 Ω
    a1-3 (AC1) - a1-2 (EAC)
    OFF switch: ON
    Approx. 329 Ω
    a1-3 (AC1) - a1-2 (EAC)
    TEMP+ switch: ON
    Approx. 1,000 Ω
    a1-3 (AC1) - a1-2 (EAC)
    TEMP- switch: ON
    Approx. 3,110 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY
OK


3. INSPECT SPIRAL CABLE SUB-ASSEMBLY

  1. I039337E26
    Disconnect the connector from the spiral cable sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    E18-10 (AC1) - a1-3 (AC1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    E18-9 (EAC) - a1-2 (EAC)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    HINT:
    The spiral cable makes a maximum of approximately 5 rotations.



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY
OK


4. CHECK HARNESS AND CONNECTOR (A/C CONTROL ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

  1. E124480E34
    Disconnect the connector from the A/C control assembly.

  1. I046136E06
    Disconnect the connector from the spiral cable sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F16-9 (ADI1) - E18-10 (AC1)
    Always
    Below 1 Ω
    F16-8 (SG) - E18-9 (EAC)
    Always
    Below 1 Ω
    F16-9 (ADI1) - Body ground
    Always
    10 kΩ or higher
    F16-8 (SG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE A/C CONTROL ASSEMBLY


← Steering Pad Switch Circuit (Oct 2006 – May 2009)IG Power Source Circuit (Jun 2006 – Sep 2006) →