2006-2011 Camry Aurion · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 from Oct 2006


1. REMOVE FRONT DRIVE SHAFT LH HOLE SNAP RING

  1. C057543E04
    Using a screwdriver, remove the front drive shaft LH hole snap ring.


2. REMOVE NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP

  1. C115612E02
    Using needle-nose pliers, remove the No. 2 front axle inboard joint boot clamp as shown in the illustration.


3. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP

  1. C147975
    Using pliers, remove the front axle inboard joint boot clamp as shown in the illustration.


4. SEPARATE FRONT AXLE INBOARD JOINT BOOT
  1. Separate the front axle inboard joint boot from the inboard joint assembly.


5. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Remove the grease from the inboard joint assembly.

  1. F045461E08
    Put matchmarks on the inboard joint assembly and outboard joint shaft.

    NOTICE:
    Do not use a punch for the marks.

  1. Remove the inboard joint assembly from the outboard joint shaft.

  1. F045046
    Using a snap ring expander, remove the shaft snap ring.

  1. C141145E01
    Put matchmarks on the outboard joint shaft and tripod joint.

    NOTICE:
    Do not use a punch for the marks.

  1. Using a brass bar and a hammer, remove the tripod joint from the outboard joint shaft.

    NOTICE:
    Do not tap the roller.


6. REMOVE FRONT AXLE INBOARD JOINT BOOT
  1. Remove the inboard joint boot from the outboard joint shaft.


7. REMOVE FRONT DRIVE SHAFT DAMPER LH (for Automatic Transaxle)

  1. C108273
    Using pliers, remove the drive shaft damper clamp as shown in the illustration.

  1. Remove the drive shaft damper.


8. REMOVE FRONT DRIVE SHAFT DAMPER RH
  1. Remove the front drive shaft damper RH.

    HINT:
    Perform the same procedures as for the front drive shaft damper LH.


9. REMOVE NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP

  1. C081167E02
    Using pliers, remove the No. 2 front axle outboard joint boot clamp as shown in the illustration.


10. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP
  1. Remove the front axle outboard joint boot clamp.

    HINT:
    Perform the same procedures as for the No. 2 front axle outboard joint boot clamp.


11. REMOVE FRONT AXLE OUTBOARD JOINT BOOT
  1. Remove the outboard joint boot from the outboard joint shaft.

  1. Remove the grease from the outboard joint.


12. REMOVE FRONT DRIVE SHAFT DUST COVER LH

  1. F040647E07
    Using SST and a press, remove the drive shaft dust cover LH.
    SST
    09950-00020  

    NOTICE:
    Be careful not to drop the inboard joint assembly.


13. REMOVE FRONT DRIVE SHAFT DUST COVER RH

  1. C067101E02
    Using a press, remove the drive shaft dust cover RH.


14. REMOVE FRONT DRIVE SHAFT DUST COVER

  1. F040208E03
    Using SST and a press, remove the drive shaft dust cover.
    SST
    09950-00020  


15. REMOVE FRONT DRIVE SHAFT BEARING

  1. C092033E04
    Using a snap ring expander, remove the drive shaft hole snap ring.

  1. F040210E04
    Using SST and a press, remove the bearing.
    SST
    09527-10011  

  1. Remove the bearing bracket hole snap ring.

    NOTICE:
    Be careful not to drop the inboard joint assembly.

← REMOVAL (from Jun 2009)DISASSEMBLY (from Oct 2006) →