2006-2011 Camry Aurion · Service Manual DRIVE LINE

REASSEMBLY

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 from Oct 2006


1. INSTALL FRONT DRIVE SHAFT BEARING

  1. C092032E01
    Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.

  1. Using SST and a steel plate, install a new front drive shaft bearing.

    SST
    09527-30010  
    09527-10011  

    NOTICE:
    Bearing should be completely installed.

  1. C092033E02
    Using a snap ring expander, install a new drive shaft hole snap ring.


2. INSTALL FRONT DRIVE SHAFT DUST COVER

  1. F045047E03
    Using SST and a press, install a new drive shaft dust cover.
    SST
    09726-40010  
    09527-10011  

    NOTICE:
    1. The dust cover should be completely installed.
    2. Be careful not to damage the dust cover.


3. INSTALL FRONT DRIVE SHAFT DUST COVER RH

  1. C129109E01
    Using SST and a press, install a new drive shaft dust cover RH until distance (A) from the tip of the center drive shaft to the drive shaft dust cover RH meets the specification.
    SST
    09527-10011  

    Distance (A):
    90.0 to 91.0 mm (3.5433 to 3.5827 in.)

    NOTICE:
    1. The dust cover should be completely installed.
    2. Be careful not to damage the dust cover.


4. INSTALL FRONT DRIVE SHAFT DUST COVER LH

  1. F041033E03
    Using SST and a press, install a new drive shaft dust cover LH.
    SST
    09527-10011  

    NOTICE:
    1. The dust cover should be completely installed.
    2. Be careful not to damage the dust cover.


5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT

  1. W001994E04
    Hold the drive shaft lightly in a vise between aluminium plates.

    HINT:
    Before installing the boots, wrap the spline of the drive shaft with vinyl tape to prevent the boots from being damaged.

  1. Temporarily install a new outboard joint boot to the drive shaft with the 2 clamps.

  1. Fill the outboard joint shaft and outboard joint boot with grease.

    Grease capacity (for Manual transaxle):
    LHD
    RHD
    175 to 195 g (6.2 to 6.9 oz.)

    Grease capacity (for Automatic transaxle):
    LHD
    RHD
    175 to 195 g (6.2 to 6.9 oz.)
    100 to 120 g (3.5 to 4.2 oz.)


6. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

  1. C106162E04
    Hold the drive shaft lightly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Install the 2 outboard joint boot clamps onto the boot.

  1. Place SST onto the outboard joint boot clamp.

    SST
    09521-24010  

  1. Tighten the SST so that the outboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten the SST.

  1. C106163E01
    Using SST, measure the clearance of the outboard joint boot clamp.
    SST
    09240-00020  

    Clearance:
    0.5 to 1.5 mm (0.0197 to 0.0591 in.)

    NOTICE:
    If the measured value is greater than the specified value, retighten the clamp.


7. INSTALL NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP
  1. Install the No. 2 outboard joint boot clamp onto the boot.

  1. R010425E04
    Place SST onto the No. 2 outboard joint boot clamp.
    SST
    09521-24010  

  1. Tighten the SST so that the No. 2 outboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten the SST.

  1. R010426E08
    Using SST, measure the clearance of the No. 2 outboard joint boot clamp.
    SST
    09240-00020  

    Clearance:
    0.5 to 1.5 mm (0.0197 to 0.0591 in.)

    NOTICE:
    If the measured value is greater than the specified value, retighten the clamp.


8. INSTALL FRONT DRIVE SHAFT DAMPER LH (for Automatic Transaxle)

  1. F040646E03
    Install the drive shaft damper to the drive shaft.

  1. Make sure that the damper is on the shaft groove.

  1. Set the distance as specified below.

    Distance:
    228.0 to 232.0 mm (8.976 to 9.134 in.)

  1. Install the drive shaft damper clamp onto the drive shaft damper.

    NOTICE:
    Be sure to install the clamp in the correct position.

  1. C108289E01
    Place SST onto the drive shaft damper clamp.
    SST
    09521-24010  

  1. Tighten the SST so that the clamp is pinched.

    NOTICE:
    Do not overtighten the SST.

  1. C108290
    Using SST, measure the clearance of the drive shaft damper clamp.
    SST
    09240-00020  

    Clearance:
    0.5 to 1.5 mm (0.0197 to 0.0591 in.)

    NOTICE:
    If the measured value is greater than the specified value, retighten the clamp.


9. INSTALL FRONT DRIVE SHAFT DAMPER RH
  1. Install the front drive shaft damper RH.

    HINT:
    Perform the same procedures as for the front drive shaft damper LH.


10. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

  1. C067417E07
    Temporarily install a new inboard joint boot to the drive shaft with the 2 clamps.

  1. Place the beveled side of the tripod joint axial spline toward the outboard joint shaft.

  1. Align the matchmarks.

  1. Using a brass bar and hammer, tap in the tripod joint to the outboard joint shaft.

    NOTICE:
    1. Do not tap the roller.
    2. Be sure to install the tripod joint assembly in the correct direction.

  1. F045046
    Using a snap ring expander, install a new shaft snap ring.

  1. Fill the outboard joint shaft and inboard joint boot with grease.

    Grease capacity:
    170 to 190 g (6.0 to 6.7 oz.)

  1. F040222E04
    Align the matchmarks and install the inboard joint assembly to the outboard joint shaft assembly.


11. INSTALL FRONT AXLE INBOARD JOINT BOOT
  1. Install the inboard joint boot to the inboard joint assembly.

  1. C148401E01
    Check whether the drive shaft dimensions are within the following specifications.

    HINT:
    The following table shows dimension (A) of the drive shaft.

    Dimension (A):
    LH
    RH
    598.0 to 602.0 mm (23.54 to 23.70 in.)
    897.0 to 901.0 mm (35.32 to 35.47 in.)


12. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

  1. D026925E03
    Hold the drive shaft lightly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Install the 2 inboard joint boot clamps onto the boot.

  1. Place SST onto the inboard joint boot clamp.

    SST
    09521-24010  

  1. Tighten the SST so that the inboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten the SST.

  1. D026926E01
    Using SST, measure the clearance of the inboard joint boot clamp.
    SST
    09240-00020  

    Clearance:
    0.5 to 1.5 mm (0.0197 to 0.0591 in.)

    NOTICE:
    If the measured value is greater than the specified value, retighten the clamp.


13. INSTALL NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP

  1. C115612E02
    Using needle nose pliers, install the No. 2 front axle inboard joint boot clamp as shown in the illustration.


14. INSTALL FRONT DRIVE SHAFT LH HOLE SNAP RING
  1. Install a new hole snap ring.


15. INSPECT FRONT DRIVE SHAFT ASSEMBLY

  1. C091598E02
    Check that there is no excessive play in the outboard joint.

  1. Check that the inboard joint slides smoothly in the thrust direction.

  1. Check that there is no excessive play in the radial directions of the inboard joint.

  1. Check the boots for damage.

← INSPECTION (from Jun 2006)REASSEMBLY (from Oct 2006) →