2006-2011 Camry Aurion · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. REMOVE FRONT WHEEL

2. REMOVE FRONT AXLE HUB NUT

  1. C108168E02
    Using SST and a hammer, release the staked part of the front axle hub nut.
    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the thread of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.


3. SEPARATE FRONT SPEED SENSOR

  1. C140592
    Remove the bolt and clip, and separate the speed sensor wire and flexible hose from the shock absorber.

  1. C132782E01
    Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.


4. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

  1. C067088E04
    Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.


5. REMOVE FRONT DISC

  1. C132801E01
    Remove the front disc.

    HINT:
    Put matchmarks on the disc and the axle hub.


6. SEPARATE TIE ROD END SUB-ASSEMBLY

  1. C108515E05
    Remove the cotter pin and nut.

  1. Using SST, separate the tie rod end sub-assembly from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Make sure that the string of SST is securely tied to the vehicle.
    2. Be careful not to damage the ball joint dust cover.
    3. Be careful not to damage the steering knuckle.
    4. Be careful not to damage the front disc brake dust cover.


7. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM

  1. F040142E01
    Remove the bolt and 2 nuts, and separate the front suspension lower No. 1 arm from the lower ball joint.


8. REMOVE FRONT AXLE ASSEMBLY

  1. C129150E01
    Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.

  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.

  1. C132414
    Remove the 2 bolts, 2 nuts, and front axle assembly.


9. REMOVE NO. 1 FRONT WHEEL BEARING DUST DEFLECTOR

  1. C108161E02
    Using a screwdriver with its tip wrapped with vinyl tape, remove the No. 1 front wheel bearing dust deflector.

    NOTICE:
    Be careful not to damage the steering knuckle.


10. REMOVE FRONT AXLE HUB HOLE SNAP RING

  1. C108210
    Using snap ring pliers, remove the front axle hub hole snap ring.


11. REMOVE FRONT AXLE HUB SUB-ASSEMBLY

  1. C108162E02
    Hold the front axle assembly between aluminium plates in a vise.

    NOTICE:
    Do not overtighten the vise.

  1. Using SST, remove the front axle hub sub-assembly.

    SST
    09520-00031  

  1. C108211E02
    Using SST and a press, remove the bearing inner race (outside) from the front axle hub sub-assembly.
    SST
    09555-55010  
    09950-60010   (09951-00430)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to drop the front axle hub sub-assembly.


12. REMOVE FRONT DISC BRAKE DUST COVER
  1. Remove the 4 bolts and disc brake dust cover from the steering knuckle.


13. REMOVE FRONT LOWER BALL JOINT ASSEMBLY

  1. C145242
    Remove the cotter pin and nut.

  1. C145243E01
    Using SST, remove the front lower ball joint.
    SST
    09628-62011  

    NOTICE:
    1. Do not damage the dust cover of the ball joint.
    2. Do not damage the steering knuckle.


14. REMOVE FRONT AXLE HUB BEARING

  1. C108212E02
    Place the bearing inner race (outside) on the front axle hub bearing.

  1. Using SST and a press, press the front axle hub bearing until it contacts the SST.

    SST
    09527-17011  
    09950-60010   (09951-00600, 09951-00400, 09952-06010)
    09950-70010   (09951-07100)

  1. C108213E02
    Using SST to make the steering knuckle horizontal, fix it to the V-block as shown in the illustration.
    SST
    09527-20011  
    09950-60010   (09951-00600, 09951-00400, 09952-06010)
    09950-70010   (09951-07100)

  1. Using SST and a press, remove the front axle hub bearing from the steering knuckle.

← REMOVAL (Oct 2006 – May 2009)INSTALLATION (Jun 2006 – Sep 2006) →