2006-2011 Camry Aurion · Service Manual ENGINE

B2276 ACCR Signal Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The main body ECU will set this DTC if the ACCR signal sent from the ECM is ON for 40 seconds or more.

HINT:
When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.

DTC No.
DTC Detection Condition
Trouble Area
B2276
ACCR output circuit inside main body ECU or other related circuit is malfunctioning
  1. Main body ECU
  2. ECM
  3. Wire harness or connector

WIRING DIAGRAM

B157572E02

INSPECTION PROCEDURE


1. CHECK DTC OUTPUT
  1. Delete the DTCs (Click here).

    HINT:
    After all DTCs are cleared, check if the trouble occurs again 50 seconds after the engine switch is turned on (IG).

  1. Check for DTCs again.

    OK:
    No DTC B2276 is output.



NG
Go to step 2
OK

CHECK INTERMITTENT PROBLEMS

2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)

  1. Disconnect the E6 ECU connector.B157571E01

  1. Disconnect the A55 ECM connector (LHD).

  1. Disconnect the A24 ECM connector (RHD).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-3 (ACCR) - A55-13 (ACCR)*1
    E6-3 (ACCR) - A24-13 (ACCR)*2
    Always
    Below 1 Ω
    E6-3 (ACCR) - Body ground
    Always
    10 kΩ or higher

    HINT:
    *1: LHD
    *2: RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT MAIN BODY ECU

  1. B138007E27
    Reconnect the connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E6-3 (ACCR) - Body ground
    Brake pedal depressed, shift P position, engine switch is pushed once → on (IG)
    0.1 to 0.8 V (*1) → output voltage at terminal AM1 or AM2 is -2 V or more.

    HINT:
    *1: Voltage is output only when the engine is cranking.



NG
REPLACE ECM
OK


4. CHECK MAIN BODY ECU OPERATION
  1. After replacing the main body ECU with a normally functioning ECU, check that the engine starts. Make sure the brake pedal is depressed and the shift position is P at this time.

  1. Check that the engine switch mode can be changed by pushing the engine switch.

    HINT:
    Without depressing the brake pedal, push the engine switch repeatedly. Engine switch mode should turn from off to on (ACC) to on (IG) and back to off. With the brake pedal depressed, push the engine switch repeatedly. Engine switch mode should turn to ENGINE START from any status.

    OK:
    Engine can start normally.

    HINT:
    If engine does not start (Click here).



NG
REPLACE ECM
OK

END (MAIN BODY ECU DEFECTIVE)


← B2276 ACCR Signal Circuit Malfunction (Oct 2006 – May 2009)B2277 Detecting Vehicle Submersion (from Oct 2006) →