2006-2011 Camry Aurion · Service Manual BODY

B2312 Driver Side Door Master Switch Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2006

DESCRIPTION

The portion of the power window control system that is located in the driver door consists of a power window master switch, regulator, and a motor with an integrated ECU. The driver door power window regulator motor is controlled by the ECU when the power window master switch is operated (models with jam protection).
When the ECU determines that the power window master switch is stuck, DTC B2312 is set.

NOTICE:
The power window control system uses a serial communication protocol (LIN) to communicate with the main body ECU. Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

DTC Code
DTC Detection Condition
Trouble Area
B2312
The power window regulator master switch is stuck
  1. Power window regulator motor (on driver side)
  2. Power window regulator master switch
  3. Wire harness
  4. Power window regulator master switch is held in same position for more than 20 seconds

WIRING DIAGRAM

B140744E09

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Using the data list to check the function of the power window power window ECU (Power window regulator motor).

    D DOOR MOTOR: 
    Item
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Auto SW
    Driver door power window auto switch signal/ON or OFF
    ON: Driver door power window auto switch operates
    OFF: Driver door power window auto switch does not operate
    -
    D Door Up SW
    Driver door power window manual up switch signal/ON or OFF
    ON: Driver door power window manual up switch operates
    OFF: Driver door power window manual up switch does not operate
    -
    D Door Down SW
    Driver door power window manual down switch signal/ON or OFF
    ON: Driver door power window manual down switch operates
    OFF: Driver door power window manual down switch does not operate
    -

    OK:
    ON (switch operates) appears on screen.

    HINT:
    When the power window operates normally, the problem has been caused by irregular switch operation (for example, the power window regulator master switch was held in the same position for more than 20 seconds).



OK
END
NG


2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
B150505E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LHD models:
    Tester Connection
    Condition
    Specified Condition
    8 (U) - 1 (E) - 4 (A)
    Auto UP
    Below 1 Ω
    8 (U) - 1 (E)
    Manual UP
    Below 1 Ω
    8 (U) - 5 (D) - 6 (B)
    OFF
    Below 1 Ω
    5 (D) - 1 (E)
    Manual DOWN
    Below 1 Ω
    4 (A) - 5 (D) - 1 (E)
    Auto DOWN
    Below 1 Ω
    RHD models:
    Tester Connection
    Condition
    Specified Condition
    1 (U) - 9 (E) - 4 (A)
    Auto UP
    Below 1 Ω
    1 (U) - 9 (E)
    Manual UP
    Below 1 Ω
    1 (U) - 5 (D) - 6 (B)
    OFF
    Below 1 Ω
    5 (D) - 9 (E)
    Manual DOWN
    Below 1 Ω
    4 (A) - 5 (D) - 9 (E)
    Auto DOWN
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH
OK


3. CHECK WIRE HARNESS (WINDOW REGULATOR MASTER SWITCH - WINDOW REGULATOR ECU)

  1. B164437E03
    Disconnect the M1 (*1), L1 (*2) and I5 (*1), H10 (*2) connectors.

    HINT:
    1. *1: LHD models
    2. *2: RHD models

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LHD models:
    Tester Connection
    Condition
    Specified Condition
    M1-8 (U) - I5-10 (UP1)
    Always
    Below 1 Ω
    M1-3 (LED) - I5-5 (LED)
    Always
    Below 1 Ω
    M1-4 (A) - I5-4 (AUTO)
    Always
    Below 1 Ω
    M1-5 (D) - I5-7 (DWN1)
    Always
    Below 1 Ω
    M1-8 (U) - Body ground
    Always
    10 kΩ or higher
    M1-3 (LED) - Body ground
    Always
    10 kΩ or higher
    M1-4 (A) - Body ground
    Always
    10 kΩ or higher
    M1-5 (D) - Body ground
    Always
    10 kΩ or higher

    Standard resistance:
    RHD models:
    Tester Connection
    Condition
    Specified Condition
    L1-1 (U) - H10-10 (UP1)
    Always
    Below 1 Ω
    L1-3 (LED) - H10-5 (LED)
    Always
    Below 1 Ω
    L1-4 (A) - H10-4 (AUTO)
    Always
    Below 1 Ω
    L1-5 (D) - H10-7 (DWN1)
    Always
    Below 1 Ω
    L1-1 (U) - Body ground
    Always
    10 kΩ or higher
    L1-3 (LED) - Body ground
    Always
    10 kΩ or higher
    L1-4 (A) - Body ground
    Always
    10 kΩ or higher
    L1-5 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVER SIDE POWER WINDOW ECU


← B2311 Driver Door Motor Malfunction (from Oct 2006)B2313 Glass Position Initialization Incomplete (Jun 2006 – Sep 2006) →