B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The driver side seat belt buckle switch circuit consists of the center airbag sensor assembly and the front seat inner belt assembly (driver side).DTC B1655/37 is recorded when a malfunction is detected in the driver side seat belt buckle switch circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1655/37 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM DTC |
Turn the ignition switch on (IG), and wait for at least 60 seconds.

Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1655/37 is not output.
- HINT:
- Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front seat inner belt assembly (driver side).
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly (driver side).
Check that the connectors (on the center airbag sensor assembly side and front seat inner belt assembly (driver side) side) are not damaged.
- OK:
- The connectors are not deformed or damaged.
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 4. CHECK WIRE HARNESS (OPEN) |
Using a service wire, connect terminals 11 (DBE+) and 12 (DBE-) of connector B.

- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
N3-1 (LBE+) - N3-3 (LBE-)
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
O24-1 (RBE+) - O24-3 (RBE-)
Always
Below 1 Ω
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 5. CHECK WIRE HARNESS (SHORT) |
Disconnect the service wire from connector B.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
N3-1 (LBE+) - N3-3 (LBE-)
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
O24-1 (RBE+) - O24-3 (RBE-)
Always
1 MΩ or higher
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 6. CHECK WIRE HARNESS (SHORT TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- for LHD:
Tester Connection
Condition
Specified Condition
N3-1 (LBE+) - Body ground
Ignition switch on (IG)
Below 1 V
N3-3 (LBE-) - Body ground
Ignition switch on (IG)
Below 1 V
- for RHD:
Tester Connection
Condition
Specified Condition
O24-1 (RBE+) - Body ground
Ignition switch on (IG)
Below 1 V
O24-3 (RBE-) - Body ground
Ignition switch on (IG)
Below 1 V
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 7. CHECK WIRE HARNESS (SHORT TO GROUND) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
N3-1 (LBE+) - Body ground
Always
1 MΩ or higher
N3-3 (LBE-) - Body ground
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
O24-1 (RBE+) - Body ground
Always
1 MΩ or higher
O24-3 (RBE-) - Body ground
Always
1 MΩ or higher
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 8. CHECK FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) |
Connect the connector to the center airbag sensor assembly and the front seat inner belt assembly (driver side).

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1655/37 is not output.
- HINT:
- Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 9. REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the front seat inner belt assembly (driver side) (Click here).
- HINT:
- Perform inspection using parts from a normal vehicle if possible.
| NEXT | |
| 10. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1655/37 is not output.
- HINT:
- Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.
- Result:
Result
Proceed to
OK
A
NG (for 2GR-FE RHD)
B
NG (except 2GR-FE RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
