2006-2011 Camry Aurion · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

NOTICE:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.


1. INSTALL SEAT POSITION SENSOR
  1. Check that the ignition switch is off.

  1. Check that the negative battery (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C133902E01
    Engage the pin and install the seat position sensor to the seat slide position sensor protector as shown in the illustration.

  1. C125585E06
    Using a 1.0 mm (0.039 in.) feeler gauge, temporarily install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).

  1. C133900
    Using a "TORX" socket (T30), tighten the "TORX" screw to install the seat position sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).

  1. Check that there is no looseness in the installation parts of the seat position sensor.

  1. Connect the connector.


2. INSTALL FRONT SEPARATE TYPE SEATBACK SPRING ASSEMBLY

  1. B148636
    Install the front separate type seatback spring assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


3. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH

  1. B148655
    Install the upper reclining adjuster inside cover LH with the screw.


4. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH

  1. B148654
    Install the upper reclining adjuster inside cover RH with the screw.


5. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH

  1. B148652
    Engage the claw.

  1. Install the lower reclining adjuster inside cover LH with the screw.


6. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH

  1. B148653
    Engage the claw.

  1. Install the lower reclining adjuster inside cover RH with the screw.


7. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Lumbar Support)

  1. B166770E01
    Install the lumbar support adjuster assembly with the 2 screws.

  1. Connect the connector.


8. INSTALL FRONT SEPARATE TYPE SEATBACK COVER

  1. B140574E01
    Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


9. INSTALL FRONT SEATBACK ASSEMBLY (w/o Airbag System)

  1. B153822E01
    Using hog ring pliers, install the front seatback assembly to the seat frame with 2 new hog rings, and attach the hooks.

  1. B153816
    Engage the 3 hooks.


10. INSTALL FRONT SEATBACK ASSEMBLY (w/ Airbag System)

  1. B153817
    Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
    2. Make sure that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.

  1. B153822E01
    Using hog ring pliers, install the front seatback assembly to the seat frame with 2 new hog rings, and attach the hooks.

  1. B153816
    Engage the 3 hooks.


11. INSTALL FRONT SEAT HEADREST SUPPORT

  1. B134683
    Engage the 2 claws to install the front seat headrest support.

    HINT:
    Use the same procedure for the RH side and LH side.


12. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY

  1. B134682E02
    Engage the 14 clamps.

  1. Install the front seatback board sub-assembly with the 2 screws.


13. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER

  1. B140572E01
    Using hog ring pliers, install the front separate type seat cushion cover to the seat cushion pad with 16 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


14. INSTALL FRONT SEAT CUSHION ASSEMBLY

  1. B153814E01
    Engage the hooks and install the front seat cushion assembly.


15. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. for LHD:

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. Connect the connector. (for Driver seat)

      B151323E01

    3. B151310E01
      Connect the connectors and engage each clamp.

    4. B152832
      Engage the 2 hooks.

  1. for RHD:

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. Connect the connector. (for Driver seat)

      B151324E01

    3. B151311E01
      Connect the connector and engage the 2 clamps.

    4. B147725
      Engage the 2 hooks.


16. INSTALL FRONT INNER SEAT CUSHION SHIELD

  1. B148648
    Engage the 2 claws.

  1. Install the front inner seat cushion shield with the screw.


17. INSTALL FRONT POWER SEAT LUMBAR SWITCH (w/ Lumbar Support)

  1. B178400
    Install the front power seat lumbar switch with the 2 screws.


18. INSTALL FRONT SEAT CUSHION SHIELD
  1. Connect the connector. (w/ lumber support)

  1. B149580
    Engage the 2 claws.

  1. Install the front seat cushion shield with the 2 screws.

  1. B153813
    Install the 2 rubber bands on the backside of the front seatback board sub-assembly.


19. INSTALL RECLINING ADJUSTER RELEASE HANDLE

  1. B148952
    Engage the claw to install the reclining adjuster release handle.


20. INSTALL VERTICAL ADJUSTING HANDLE (for Driver Seat)

  1. B139104
    Install the No. 2 vertical adjusting handle with the 2 screws.


21. INSTALL VERTICAL ADJUSTER COVER LH (for Driver Seat)

  1. B148953
    Engage the 2 claws to install the vertical adjuster cover.

← REASSEMBLY (Oct 2006 – May 2009)INSTALLATION (Jun 2006 – Sep 2006) →