REASSEMBLY
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
- NOTICE:
- Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.
| 1.
INSTALL FRONT SEPARATE TYPE SEATBACK SPRING ASSEMBLY |
 |
- Install the front separate type seatback spring assembly with the 4 bolts.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 2.
INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH |
 |
- Install the upper reclining adjuster inside cover LH with the screw.
| 3.
INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH |
 |
- Install the upper reclining adjuster inside cover RH with the screw.
| 4.
INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH |
 |
- Engage the claw.
Install the lower reclining adjuster inside cover LH with the screw.
| 5.
INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH |
 |
- Engage the claw.
Install the lower reclining adjuster inside cover RH with the screw.
| 6.
INSTALL FRONT SEPARATE TYPE SEATBACK COVER |
 |
- Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with 10 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 7.
INSTALL FRONT SEATBACK ASSEMBLY |
 |
- Using hog ring pliers, install the front seatback assembly to the seat frame with 2 new hog rings, and attach the hooks.
- Engage the 3 hooks.
| 8.
INSTALL FRONT SEAT HEADREST SUPPORT |
 |
- Engage the 2 claws to install the front seat headrest support.
- HINT:
- Use the same procedure for the RH side and LH side.
| 9.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY |
 |
- Engage the 2 claws.
Engage the 14 claws.
Install the front seatback board sub-assembly with the 2 screws.
| 10.
INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER |
 |
- Using hog ring pliers, install the front separate type seat cushion cover to the seat cushion pad with 16 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 11.
INSTALL FRONT SEAT CUSHION ASSEMBLY |
 |
- Engage the hooks and install the front seat cushion assembly.
| 12.
INSTALL FRONT INNER SEAT CUSHION SHIELD |
 |
- Engage the 2 claws.
Install the front inner seat cushion shield with the screw.
| 13.
INSTALL FRONT SEAT INNER BELT ASSEMBLY
|
 |
- for LHD:
Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
- Connect the connectors and engage each clamp.
- Engage the 2 hooks.
- for RHD:
Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connectors and engage each clamp.
Engage the 2 hooks.
| 14.
INSTALL FRONT SEAT CUSHION SHIELD |
 |
- Engage the 2 claws.
Install the front seat cushion shield with the 2 screws.
- Install the 2 rubber bands on the backside of the front seatback board sub-assembly.
| 15.
INSTALL RECLINING ADJUSTER RELEASE HANDLE |
 |
- Engage the claw to install the reclining adjuster release handle.