REASSEMBLY
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
- NOTICE:
- Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.
| 1.
INSTALL FRONT SEPARATE TYPE SEATBACK SPRING ASSEMBLY |
 |
- Install the front separate type seatback spring assembly with the 4 bolts.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 2.
INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH |
 |
- Install the upper reclining adjuster inside cover LH with the screw.
| 3.
INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH |
 |
- Install the upper reclining adjuster inside cover RH with the screw.
| 4.
INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH |
 |
- Engage the claw.
Install the lower reclining adjuster inside cover LH with the screw.
| 5.
INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH |
 |
- Engage the claw.
Install the lower reclining adjuster inside cover RH with the screw.
| 6.
INSTALL FRONT SEPARATE TYPE SEATBACK COVER (for Except Sports Seat Type) |
 |
- Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with 12 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 7.
INSTALL FRONT SEPARATE TYPE SEATBACK COVER (for Sports Seat Type) |
 |
- Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with 14 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 8.
INSTALL FRONT SEATBACK ASSEMBLY (for Except Sports Seat Type) |
 |
Install the front seatback assembly to the front seatback spring assembly.
- Install the front seatback cover bracket with the nut.
-
Torque:
- 5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
- NOTICE:
- For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
- Make sure that the strap is not twisted after installing the bracket.
- Install the bracket securely.
- Engage the 6 hooks.
Using hog ring pliers, install 5 new hog rings.
- Using hog ring pliers, install 3 new hog rings.
| 9.
INSTALL FRONT SEATBACK ASSEMBLY (for Sports Seat Type) |
 |
- Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.
-
Torque:
- 5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
- NOTICE:
- For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
- Make sure that the strap is not twisted after installing the bracket.
- Install the bracket securely.
Engage the 3 hooks.
- Using hog ring pliers, install 2 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 10.
INSTALL FRONT SEAT HEADREST SUPPORT |
 |
- Engage the 2 claws to install the front seat headrest support.
- HINT:
- Use the same procedure for the RH side and LH side.
| 11.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for Except Sports Seat Type) |
 |
- Engage the 4 claws.
Install the front seatback board sub-assembly with the 2 screws.
| 12.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for Sports Seat Type) |
 |
- Engage the 2 claws.
Engage the 14 claws.
Install the front seatback board sub-assembly with the 2 screws.
| 13.
INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER (for Except Sports Seat Type) |
 |
- Using hog ring pliers, install the front separate type seat cushion cover to the seat cushion pad with 14 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 14.
INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER (for Sports Seat Type) |
 |
- Using hog ring pliers, install the front separate type seat cushion cover to the seat cushion pad with 14 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 15.
INSTALL FRONT SEAT CUSHION ASSEMBLY |
 |
- Engage the hooks and install the front seat cushion assembly.
| 16.
INSTALL FRONT SEAT INNER BELT ASSEMBLY
|
 |
- for LHD:
Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
- Connect the connectors and engage each clamp.
- Engage the 2 hooks.
- for RHD:
Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connectors and engage each clamp.
Engage the 2 hooks.
| 17.
INSTALL FRONT INNER SEAT CUSHION SHIELD |
 |
Engage the 2 claws.
- Install the front inner seat cushion shield with the screw.
| 18.
INSTALL FRONT SEAT CUSHION SHIELD |
 |
Engage the 2 claws.
- Install the front seat cushion shield with the 2 screws.
- Install the 2 rubber bands on the backside of the front seatback board sub-assembly.
| 19.
INSTALL RECLINING ADJUSTER RELEASE HANDLE |
 |
- Engage the claw to install the reclining adjuster release handle.