2006-2011 Camry Aurion · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009


1. INSTALL LICENSE PLATE LIGHT ASSEMBLY LH

  1. E136251
    Engage the 2 claws to install the license plate light assembly.

  1. Connect the connector.


2. INSTALL LICENSE PLATE LIGHT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


3. INSTALL REAR LIGHT ASSEMBLY LH

  1. E192205
    Engage the pin and install the rear light assembly.

  1. Install the 3 nuts.

    Torque:
    3.6 N*m{ 37 kgf*cm , 32 in.*lbf }

  1. Connect the connector.


4. INSTALL REAR LIGHT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


5. INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/ Rear View Monitor System)
w/o Smart Entry and Start System: (Click here)
w/ Smart Entry and Start System: (Click here)

6. INSTALL LUGGAGE DOOR OPENING SWITCH ASSEMBLY (w/ Smart Entry and Start System)

  1. w/o Rear View Monitor System:

    1. B212895
      Install the luggage door opening switch assembly with the 2 screws.

    2. Engage the 2 clamps.

  1. w/ Rear View Monitor System:

    1. B212894
      Install the luggage door opening switch assembly with the 2 screws.

    2. Engage the 2 clamps.

    3. Connect the connector.


7. INSTALL LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH ASSEMBLY

  1. B135462
    Engage the 2 clips and install the luggage compartment door outside garnish assembly.

  1. B135460
    Install the 3 nuts.


8. INSTALL REAR SPOILER (w/ Rear Spoiler)

HINT:
When installing the spoiler, heat the vehicle body and spoiler using a heat light.

Heating temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Spoiler
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body and rear spoiler excessively.

  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Clean the rear spoiler. (If reusing the rear spoiler)

    1. Using a heat light, heat the rear spoiler.

    2. Remove the double-sided tape from the rear spoiler.

    3. Wipe off any tape adhesive residue with cleaner.

    4. Apply new double-sided tape to the rear spoiler.

      B137017E01

  1. B137018
    Install the rear spoiler.

    1. Using a heat light, heat the vehicle body and rear spoiler.

    2. Remove the release paper from the rear spoiler.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Engage the 4 clips and install the rear spoiler with the 2 nuts.


9. INSTALL LUGGAGE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY

  1. B136497
    Install the luggage compartment door lock cylinder with the 2 nuts.

  1. B136496
    Connect the cable and connector.


10. INSTALL LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

  1. B136493
    Install the luggage compartment door lock assembly with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.

  1. B136492
    Connect the rod.


11. INSTALL LUGGAGE COMPARTMENT DOOR COVER

  1. B135458
    Install the luggage compartment door cover with the 13 clips.

← REASSEMBLY (Jun 2006 – May 2009)COMPONENTS (Oct 2006 – May 2009) →