2006-2011 Camry Aurion · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL GENERATOR ASSEMBLY

  1. A135391
    Install the bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A128066
    Install the wire harness clamp stay.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. A133867
    Connect the wire harness clamp.

  1. Install the generator assembly to the cylinder block with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A133866
    Install the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. A133865
    Connect the generator connector to the generator assembly.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the 2 wire harness clamps.

  1. Connect the magnetic clutch connector to the compressor and magnetic clutch.


2. INSTALL V-RIBBED BELT

  1. A129622E01
    Install the V-ribbed belt.

  1. Using SST, turn the belt tensioner counterclockwise and remove the bar.

    SST
    09249-63010  

  1. A129623E02
    If it is difficult to install the V-ribbed belt, perform the following procedure:

    1. Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.

    2. While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the tensioner pulley.

      NOTICE:
      1. Put the backside of the V-ribbed belt on the tensioner pulley and idler pulley.
      2. Check that the V-ribbed belt is properly set to each pulley.

  1. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the belt has not slipped out of the grooves on the bottom of the crank pulley by hand.


3. INSTALL RADIATOR ASSEMBLY

  1. A135523
    Install the radiator to the body.

  1. A133370
    Install the condenser assembly with the 4 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


4. INSTALL FAN SHROUD

  1. A143825E01
    Install the fan assembly with motor to the radiator with the 2 guides at the bottom and 3 snap fits on the top.

  1. A160127E01
    Connect the fan motor connector and 3 clamps.


5. INSTALL RADIATOR SUPPORT UPPER

  1. A149528
    Install the radiator support upper with the 5 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 horn connectors.


6. CONNECT NO. 1 OIL COOLER OUTLET HOSE

  1. A133366
    Connect the No. 1 oil cooler outlet hose to the radiator assembly.


7. CONNECT NO. 1 OIL COOLER INLET HOSE

  1. A133365
    Connect the No. 1 oil cooler inlet hose to the radiator assembly.


8. CONNECT RADIATOR OUTLET HOSE

  1. A133364
    Connect the radiator outlet hose to the radiator assembly.


9. CONNECT RADIATOR INLET HOSE

  1. A146039
    Connect the radiator inlet hose to the radiator assembly.


10. CONNECT RADIATOR RESERVOIR TANK HOSE

  1. A133362
    Connect the radiator reservoir tank hose to the radiator assembly.


11. INSTALL FRONT BUMPER ENERGY ABSORBER

  1. B159632
    Install the front bumper energy absorber to the front bumper reinforcement sub-assembly.


12. INSTALL FRONT BUMPER ASSEMBLY (w/o Fog Light)

  1. B160026
    Engage each claw.

  1. Install the front bumper assembly with the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B149627
    Install the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.


13. INSTALL FRONT BUMPER ASSEMBLY (w/ Fog Light)

  1. B160029
    Connect each connector.

  1. Engage each claw.

  1. Install the front bumper assembly with the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B149627
    Install the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.


14. INSTALL FRONT BUMPER ASSEMBLY (w/ Clearance Sonar System)

  1. B160029
    Connect each connector.

  1. Engage each claw.

  1. Install the front bumper assembly with the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B149627
    Install the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.


15. INSTALL FRONT BUMPER ASSEMBLY (w/ Headlight Cleaner System)

  1. B149621
    Connect the headlight cleaner washer hose.

  1. Connect each connector.

  1. B160029
    Engage each claw.

  1. Install the front bumper assembly with the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B149627
    Install the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.


16. INSTALL NO. 1 AIR CLEANER INLET

  1. A132970
    Install the No. 1 air cleaner inlet with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


17. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A135706
    Install the air cleaner cap sub-assembly, and connect the 3 bands.

  1. A135705E01
    Connect the mass air flow meter connector (*1).

  1. Connect the No. 2 ventilation hose (*2).

  1. Connect the hose band (*3).

  1. A135704
    Connect the 3 vacuum hoses.


18. INSTALL AIR CLEANER INLET ASSEMBLY

  1. A132969
    Install the air cleaner inlet with the clamp and 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.9 N*m{ 70 kgf*cm , 61 in.*lbf }


20. ADD ENGINE COOLANT
  1. Close the radiator drain cock plug and 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    9.0 liters (9.5 US qts, 7.9 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


21. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch OFF.

  1. A133894
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


22. INSTALL V-BANK COVER SUB-ASSEMBLY

  1. A140800
    Fit the 3 retainers and install the V-bank cover.


23. INSTALL COOL AIR INTAKE DUCT SEAL

  1. A141576E01
    Install the intake duct seal with the 7 clips.


24. INSTALL FRONT FENDER APRON SEAL RH

25. INSTALL ENGINE UNDER COVER RH

26. INSTALL ENGINE UNDER COVER LH

27. INSTALL FRONT WHEEL RH
← REASSEMBLY (from Jun 2009)INSTALLATION (from Jun 2009) →