2006-2011 Camry Aurion · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE FRONT WHEEL RH

3. REMOVE FRONT FENDER APRON SEAL RH

4. REMOVE ENGINE UNDER COVER RH

5. REMOVE ENGINE UNDER COVER LH

6. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs, then drain the coolant.

    A128117E02

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


7. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A140800
    Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.


8. REMOVE COOL AIR INTAKE DUCT SEAL

  1. A141576E01
    Remove the 7 clips and intake duct seal.


9. REMOVE AIR CLEANER INLET ASSEMBLY

  1. A132969
    Remove the 2 bolts, clamp and air cleaner inlet.


10. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A135704
    Disconnect the 3 vacuum hoses.

  1. A135705E01
    Disconnect the mass air flow meter connector (*1).

  1. Disconnect the No. 2 ventilation hose (*2).

  1. Disconnect the hose band (*3).

  1. A135706
    Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.


11. REMOVE NO. 1 AIR CLEANER INLET

  1. A132970
    Remove the bolt and No. 1 air cleaner inlet.


12. REMOVE FRONT BUMPER ASSEMBLY (w/o Fog Light)

  1. B160025E01
    Put protective tape around the front bumper assembly.

  1. B149626E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B160026
    Remove the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B160027
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Remove the front bumper assembly.


13. REMOVE FRONT BUMPER ASSEMBLY (w/ Fog Light)

  1. B160028E01
    Put protective tape around the front bumper assembly.

  1. B149626E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B160029
    Remove the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B159433
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each connector, and then remove the front bumper assembly.


14. REMOVE FRONT BUMPER ASSEMBLY (w/ Clearance Sonar System)

  1. B160028E01
    Put protective tape around the front bumper assembly.

  1. B149626E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B160029
    Remove the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B159433
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each connector, and then remove the front bumper assembly.


15. REMOVE FRONT BUMPER ASSEMBLY (w/ Headlight Cleaner System)

  1. B160028E01
    Put protective tape around the front bumper assembly.

  1. B149626E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B160029
    Remove the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B159433
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each connector.

  1. B149621
    Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.


16. REMOVE FRONT BUMPER ENERGY ABSORBER

  1. B159632
    Remove the front bumper energy absorber from the front bumper reinforcement sub-assembly.


17. SEPARATE RADIATOR RESERVOIR TANK HOSE

  1. A133362
    Disconnect the radiator reserve tank hose from the radiator assembly.


18. DISCONNECT RADIATOR INLET HOSE

  1. A146039
    Disconnect the radiator inlet hose from the radiator assembly.


19. DISCONNECT RADIATOR OUTLET HOSE

  1. A133364
    Disconnect the radiator outlet hose from the radiator assembly.


20. DISCONNECT NO. 1 OIL COOLER INLET HOSE

  1. A133003E01
    Remove the clamp and disconnect the oil cooler inlet hose.


21. DISCONNECT NO. 1 OIL COOLER OUTLET HOSE
  1. Remove the clamp and disconnect the oil cooler outlet hose.


22. REMOVE RADIATOR SUPPORT UPPER
  1. Disconnect the horn connectors.

  1. A149528
    Remove the 5 bolts and radiator support upper.


23. REMOVE FAN SHROUD

  1. A160127E01
    Remove the 3 clamps and connector.

  1. A143825E01
    Release the 3 snap fits and lift the fan assembly with motor from the radiator.


24. REMOVE RADIATOR ASSEMBLY

  1. A133370
    Remove the 4 bolts and separate the condenser assembly from the radiator assembly.

  1. A133373
    Remove the radiator assembly from the body.


25. REMOVE V-RIBBED BELT

  1. A129622E01
    Using SST, release the belt tension by turning the belt tensioner counterclockwise, and remove the V-ribbed belt from the belt tensioner.
    SST
    09249-63010  

  1. A095070
    While turning the belt tensioner counterclockwise, align with its holes, and then insert a 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner.


26. REMOVE GENERATOR ASSEMBLY

  1. A133865
    Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector from the generator assembly.

  1. Disconnect the connector from the compressor and magnetic clutch.

  1. Disconnect the 2 wire harness clamps.

  1. A133866
    Remove the 2 bolts.

  1. A133867
    Remove the bolt from the cylinder block.

  1. Disconnect the wire harness clamp and remove the generator assembly.

  1. A128066
    Remove the bolt and wire harness clamp stay.

  1. A135391
    Remove the bolt and bracket.

← COMPONENTS (from Jun 2009)REMOVAL (from Jun 2009) →