2006-2011 Camry Aurion · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A128081E01
    Using SST and a press, press in a new generator drive end frame bearing.
    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)

  1. A137712E01
    Fit the tabs on the retainer plate into the cutouts on the drive end frame to install the retainer plate.

  1. Install the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Place the drive end frame on the clutch pulley.

  1. A118367E01
    Install the generator rotor assembly to the drive end frame.

  1. A118365E01
    Place a new generator washer on the generator rotor.


3. INSTALL GENERATOR COIL ASSEMBLY

  1. A128082E03
    Using a deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.

  1. A128074
    Install the 4 bolts.

    Torque:
    5.8 N*m{ 59 kgf*cm , 51 in.*lbf }


4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A079315E13
    While pushing the 2 brushes into the generator brush holder assembly, insert a φ1.0 mm (0.039 in.) pin into the brush holder hole.

  1. A079316E02
    Install the brush holder assembly to the generator coil with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. Pull out the pin from the generator brush holder.


5. INSTALL GENERATOR TERMINAL INSULATOR

  1. A128083E01
    Install the terminal insulator to the generator coil.

    NOTICE:
    Pay attention to installation direction of the terminal insulator.


6. INSTALL GENERATOR REAR END COVER

  1. A128071
    Install the generator rear end cover to the generator coil with the 3 nuts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }


7. INSTALL GENERATOR CLUTCH PULLEY
  1. Temporarily install the clutch pulley onto the rotor shaft.

  1. A128084E01
    Set SST (A) and (B).
    SST
    09820-63020  

  1. A135194E01
    Clamp SST (A) in a vise.

  1. Place the rotor shaft end into SST (A).

  1. A135195E01
    Fit SST (B) to the clutch pulley.

  1. A151433E01
    Tighten the pulley by turning SST (B) in the direction shown in the illustration.

    Torque:
    without SST:
    110 N*m{ 1125 kgf*cm , 81 ft.*lbf }
    with SST:
    84 N*m{ 857 kgf*cm , 62 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 318 mm (12.52 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.

  1. Remove the generator assembly from the SST.

  1. Check that the clutch pulley rotates smoothly.

  1. Install a new clutch pulley cap to the clutch pulley.

← INSPECTION (from Jun 2009)REASSEMBLY (from Jun 2009) →