2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

  1. B132833
    Disengage the 2 clips and remove the front door lower frame bracket garnish.


2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

  1. B132834E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.


3. REMOVE ASSIST GRIP COVER

  1. B132836E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the assist grip cover.


4. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. B132838E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.

  1. Disconnect the connector.


5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

  1. B132840E01
    Remove the 3 screws and clip (A).

  1. Using a clip remover, disengage the 9 clips.

  1. B136401E01
    Pull up the front door trim board in the direction indicated by the arrow.

  1. Disengage the reference bosses from the front door panel.

  1. Raise the front door trim board to disengage the 4 claws and remove the front door trim board together with the front door inner glass weatherstrip.

  1. B136403
    Disengage the 2 claws and disconnect the front door inside handle sub-assembly.


6. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

  1. B136404
    Using a screwdriver, disengage the 4 clips as shown in the illustration and remove the front door inner glass weatherstrip from the front door trim board.


7. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

  1. B136408
    Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door inside handle sub-assembly.


8. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

  1. E129164
    Disconnect the connector.

  1. Remove the 4 bolts and front No. 1 speaker assembly.

    NOTICE:
    Do not touch the cone part of the speaker.


9. REMOVE FRONT DOOR SERVICE HOLE COVER

  1. B136410E01
    Disconnect the connector and each clamp, and remove the front door service hole cover.

    HINT:
    Remove the remaining butyl tape on the door.


10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the front power window regulator motor assembly connector.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. B136412
    Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, the door glass may fall, causing damage.

  1. B136413E01
    Remove the front door glass sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.

  1. Disconnect the power window regulator master switch assembly and front power window regulator motor assembly connector.


11. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

  1. B136420E01
    Remove the bolt and the front door rear lower frame sub-assembly as shown in the illustration.


12. REMOVE FRONT DOOR OUTSIDE HANDLE COVER

  1. B136421
    Remove the hole plug.

  1. Using a "TORX" socket wrench (T30), loosen the screw and remove the front door outside handle cover and the door lock key cylinder as a unit.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

  1. B136424
    Using a screwdriver, disengage the 2 claws and remove the front door outside handle cover.


13. REMOVE FRONT DOOR LOCK ASSEMBLY

  1. B136428
    Disconnect the connector.

  1. Using a "TORX" socket wrench (T30), remove the 3 screws.

  1. Slide the front door lock assembly downward, pull out the front door lock open rod from the outside handle frame, and remove the front door lock assembly and cables as a unit.

  1. Remove the front door lock open rod from the front door lock assembly.

  1. Remove the door lock wiring harness seal from the front door lock assembly.

  1. B136430
    Remove the front door lock remote control cable assembly.

  1. B136431
    Using a screwdriver, disengage the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B136432
    Remove the front door inside locking cable assembly.

← REMOVAL (Jun 2006 – Sep 2006)REMOVAL (from Jun 2009) →