2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. REMOVE COOL AIR INTAKE DUCT SEAL (for Front Side)

  1. B161416
    Remove the 7 clips and cool air intake duct seal.


2. REMOVE FRONT BUMPER ASSEMBLY (for Front Side)

  1. B160028E01
    Put protective tape around the front bumper assembly.

  1. B149626E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B160029
    Remove the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B159433
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each connector, and then remove the front bumper assembly.


3. REMOVE NO. 1 ULTRASONIC SENSOR (for Front Side)
  1. Disconnect the sensor connector.

  1. E134853
    While pushing down on the lever with a finger to release the claw, disengage the claw on the other side to remove the No. 1 ultrasonic sensor.

    HINT:
    The type of the claw on the top and bottom of the sensor are different. Observe the claws carefully before attempting to remove the sensor.


4. REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (for Front Side)

  1. E134854
    Disengage the 2 claws and remove the No. 1 ultrasonic sensor retainer from the front bumper.


5. REMOVE LUGGAGE COMPARTMENT FLOOR MAT (for Rear Side)

6. REMOVE SPARE WHEEL COVER CLAMP (for Rear Side)

7. REMOVE SPARE WHEEL COVER ASSEMBLY (for Rear Side)

8. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for Rear Side)

  1. B136879
    Remove the 2 screws and the 2 No. 1 luggage compartment trim hooks.


9. REMOVE REAR FLOOR FINISH PLATE (for Rear Side)

  1. B136852
    Disengage the 7 clips and remove the rear floor finish plate.


10. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER RH (for Rear Side)

  1. B136855
    Remove the 2 clips and the luggage compartment inner trim cover RH.


11. REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH (w/o Rear Lower Spoiler)

  1. B137209
    Remove the 3 screws and rear quarter panel mudguard sub-assembly LH.


12. REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY RH (w/o Rear Lower Spoiler)

HINT:
Use the same procedure for the RH side and the LH side.


13. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler)

  1. B138885E01
    Remove the 4 screws, 2 clips, 3 nuts and rear floor board.


14. REMOVE REAR BUMPER ASSEMBLY (for Rear Side)

  1. without Rear Lower Spoiler:

    1. B149446
      Disconnect the connector.

    2. Disengage the grommet.

    3. B149447E01
      Put protective tape around the rear bumper assembly.

    4. B149448
      Using a screwdriver, open the 2 rear bumper plates.

      HINT:
      Tape the screwdriver tip before use.

    5. B149450
      Remove the 6 screws and 2 clips.

    6. B149451
      Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

      HINT:
      Use the same procedure for the RH side and LH side.

    7. Disengage each No. 2 luggage room wire clamp from the rear bumper reinforcement sub-assembly.

    8. Remove the rear bumper assembly.

  1. with Rear Lower Spoiler:

    1. B149446
      Disconnect the connector.

    2. Disengage the grommet.

    3. B160683E01
      Put protective tape around the rear bumper assembly.

    4. B160684
      Using a screwdriver, open the 2 rear bumper plates.

      HINT:
      Tape the screwdriver tip before use.

    5. B160685
      Remove the 6 screws.

    6. B160687
      Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

      HINT:
      Use the same procedure for the RH side and LH side.

    7. Disengage each No. 2 luggage room wire clamp from the rear bumper reinforcement sub-assembly.

    8. Remove the rear bumper assembly.


15. REMOVE NO. 2 ULTRASONIC SENSOR (for Rear Side)
  1. Disconnect the sensor connector.

  1. E134860
    Remove the sensor retainer as shown in the illustration.

  1. E134861
    While pushing down on the lever with a finger to release the claw, disengage the claw on the other side to remove the No. 2 ultrasonic sensor.

    HINT:
    The type of the claw on the top and bottom of the sensor are different. Observe the claws carefully before attempting to remove the sensor.


16. REMOVE NO. 2 ULTRASONIC SENSOR RETAINER (for Rear Side)

  1. E134862
    Disengage the 2 claws and remove the No. 2 ultrasonic sensor retainer from the rear bumper.


17. REMOVE NO. 1 ULTRASONIC SENSOR (for Rear Side)
  1. Disconnect the sensor connector.

  1. E134853
    While pushing down on the lever with a finger to release the claw, disengage the claw on the other side to remove the No. 1 ultrasonic sensor.

    HINT:
    The type of the claw on the top and bottom of the sensor are different. Observe the claws carefully before attempting to remove the sensor.


18. REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (for Rear Side)

  1. E134854
    Disengage the 2 claws and remove the No. 1 ultrasonic sensor retainer from the rear bumper.

← COMPONENTS (from Oct 2006)REMOVAL (from Jun 2009) →