2006-2011 Camry Aurion · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL CYLINDER HEAD GASKET

  1. A126929E01
    Place a new gasket on the cylinder block surface with the Lot No. stamp facing upward.

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Make sure that the gasket is installed in the correct direction.


2. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
The cylinder head set bolts are tightened in 2 progressive steps.

  1. Apply a light coat of engine oil to the bolt threads and the area beneath the bolt heads that come in contact with the washers.

  1. Install the bolts and plate washers to the cylinder head.

    NOTICE:
    Do not drop the washers into the cylinder head.

  1. F050595E06
    Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

  1. A098364E01
    Mark the front side of the cylinder head set bolt with paint.

  1. Retighten the cylinder head set bolts 90° in the order shown in the illustration.

  1. Check that the paint mark is now at a 90° angle to the front.


3. CONNECT ENGINE WIRE

  1. A098748E01
    Connect the ground cable with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Connect the camshaft position sensor connector.

  1. Connect the engine coolant temperature sensor connector.

  1. Connect the engine oil pressure switch connector.

  1. Connect the radio setting condenser connector.


4. CONNECT HEATER WATER HOSE INLET

5. CONNECT RADIATOR HOSE INLET

  1. A134907
    Install the clamp and connect the No. 1 radiator hose.


6. INSTALL NO. 2 CAMSHAFT BEARING

  1. A128879
    Install the No. 2 camshaft bearing.


7. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A093611E01
    Apply a light coat of engine oil to an O-ring of the camshaft timing oil control valve assembly sensor.

  1. A124556
    Install the camshaft timing oil control valve assembly sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the camshaft timing oil control valve assembly connector.


8. INSTALL CAMSHAFTS
  1. Apply a light coat of engine oil to the journal portion of the camshaft.

  1. F050592E01
    Place the 2 camshafts on the cylinder head with the No. 1 cam lobes facing the directions shown in the illustration.

  1. F050591E01
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. F050596E05
    Using several steps, uniformly tighten the 20 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    No. 1 and No. 2 bearing cap:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }
    No. 3 bearing cap:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


9. INSTALL CHAIN SUB-ASSEMBLY

HINT:
Click here.


10. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
  1. Install a new gasket onto the cylinder head.

  1. Temporarily tighten the exhaust manifold converter with the 5 nuts.

  1. A112190E01
    Tighten the 5 nuts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 378 kgf*cm , 27 ft.*lbf }

  1. A098744E01
    Connect the air-fuel ratio sensor connector.

  1. A112189
    Install the exhaust manifold heat insulator with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


11. INSTALL NO. 2 MANIFOLD STAY

  1. A112192
    Install the stay with the bolt and nut.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


12. INSTALL MANIFOLD STAY

  1. A112193
    Install the stay with the bolt and nut.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


13. INSTALL OIL LEVEL GAUGE GUIDE

  1. A112218
    Apply a light coat of engine oil to a new O-ring and install it to the guide.

  1. Install the oil level gauge guide with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


14. INSTALL OIL LEVEL GAUGE SUB-ASSEMBLY

15. INSTALL GENERATOR ASSEMBLY

  1. A097394E03
    Confirm that the wire harness of the crankshaft position sensor is secured to the wire harness clamp bracket through the back of the rib of the timing chain cover.

  1. A142104E01
    Install the generator assembly with the 2 bolts.

    Torque:
    Bolt A:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf }
    Bolt B:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. A135170
    Install the generator wire to terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the clamp bracket with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Attach the clamp and connect the generator connector to the generator.


16. INSTALL V-RIBBED BELT

  1. A114351E03
    Using SST and a 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then install the V-ribbed belt.
    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply more force than necessary.

  1. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Check to confirm that the belt has not slipped out of the grooves on the bottom of the crank pulley by hand.


17. INSTALL NO. 2 ENGINE MOUNTING BRACKET RH

  1. A134911
    Install the No. 2 engine mounting bracket RH with the 3 bolts.

    Torque:
    52 N*m{ 531 kgf*cm , 38 ft.*lbf }


18. INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

  1. A134910
    Install the engine moving control rod with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

  1. A134909
    Install the ground cable with the bolt.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }


19. INSTALL NO. 2 ENGINE MOUNTING STAY RH

  1. A134912
    Install the No. 2 engine mounting stay RH with the 2 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }


20. INSTALL FRONT EXHAUST PIPE ASSEMBLY

HINT:
Click here.


21. INSTALL NO. 1 INTAKE MANIFOLD INSULATOR

  1. A134343
    Install the No. 1 intake manifold insulator onto the cylinder block.


22. INSTALL INTAKE MANIFOLD

  1. A090130E02
    Install a new gasket into the intake manifold.

  1. A128862
    Install the intake manifold with the 5 bolts and 2 nuts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


23. INSTALL FUEL DELIVERY PIPE WITH INJECTOR

  1. A147098
    Install 4 new insulators into the cylinder head.

  1. Install the 2 delivery pipe spacers onto the cylinder head.

  1. A097444E02
    Install the fuel delivery pipe together with the 4 fuel injectors, then temporarily tighten the 2 bolts.

    NOTICE:
    Be careful not to drop the fuel injectors when installing the fuel delivery pipe.

  1. Check that the fuel injector rotates smoothly.
    If the fuel injector does not rotate smoothly, replace the O-ring.

  1. A147099
    Tighten the 2 bolts to the specified torque.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A147100
    Connect the 4 fuel injector connectors.

  1. Install the 2 wire harness clamps.


24. CONNECT FUEL TUBE SUB-ASSEMBLY

  1. A136017E01
    Install the fuel tube to the fuel hose clamp.

  1. A103968E03
    Push the fuel tube connector until it makes a "click" sound.

  1. A136015E01
    Install the No. 1 fuel pipe clamp.


25. INSTALL THROTTLE BODY

  1. A124566
    Install a new gasket onto the intake manifold.

  1. A128921E01
    Connect the purge line hose to the throttle body.

  1. Connect the water by-pass hose to the throttle body.

  1. Connect the No. 2 water by-pass hose to the throttle body.

  1. Connect the No. 1 throttle body hose to the throttle body.

  1. A128920E01
    Install the throttle body and fuel pipe clamp with the 4 bolts.

    Torque:
    30 N*m{ 305 kgf*cm , 22 ft.*lbf }

  1. Connect the fuel tube into the clamp.

  1. A128919E01
    Connect the throttle position sensor connector.

  1. Connect the wire harness clamp.


26. INSTALL BATTERY
  1. Install the battery and battery tray.

  1. A134906
    Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    Nut:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }


27. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  1. A134905
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose clamp.


28. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element onto the air cleaner case.

  1. A135670
    Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.

  1. A236553E01
    Connect the No. 1 air cleaner hose to the throttle body and unfasten the No. 1 air cleaner hose clamp.

    NOTICE:
    1. Match each concave area concavity of the air cleaner hose with the bolt of the throttle body.
    2. Make sure that the hose clamp is at the correct angle.

  1. A146036
    Connect the No. 2 ventilation hose to the air cleaner hose.

  1. A135666E02
    Connect the purge line hose to the clamp (*1).

  1. Connect the 2 purge VSV vacuum hoses (*2).

  1. Connect the purge VSV connector (*3).

  1. Connect the mass air flow meter connector (*4).


29. INSTALL AIR CLEANER INLET ASSEMBLY

  1. A134903
    Install the air cleaner inlet with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


30. INSTALL COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY

  1. C141972E01
    Install the cowl top outer front panel sub-assembly with the 4 nuts, the 4 bolts and the clamp.

    Torque:
    Nut:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }
    Bolt:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


31. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:
Click here.


32. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.9 N*m{ 70 kgf*cm , 61 in.*lbf }


33. ADD ENGINE OIL
  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Add new oil.

    Standard capacity:
    Item
    Standard Condition
    Drain and refill with oil filter change
    4.3 liters (4.5 US qts, 3.8 Imp. qts)
    Drain and refill without oil filter change
    4.1 liters (4.3 US qts, 3.6 Imp. qts)
    Dry fill
    5.0 liters (5.3 US qts, 4.4 Imp. qts)

  1. Install the oil filler cap.


34. INSPECT FOR FUEL LEAK

HINT:
Click here.


35. ADD ENGINE COOLANT
  1. Close the radiator drain cock plug and cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    6.7 liters (7.1 US qts, 5.9 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


36. INSPECT FOR COOLANT LEAK

NOTICE:
Before performing each inspection, turn the A/C switch OFF.

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A135234
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


37. INSPECT FOR ENGINE OIL LEAKS

38. INSPECT FOR EXHAUST GAS LEAK

39. INSPECT IGNITION TIMING
  1. Warm up the engine.

  1. C139987E06
    When using the intelligent tester:
    Check the ignition timing.

    1. Connect the intelligent tester to the DLC3.

    2. Enter DATA LIST MODE on the intelligent tester.

      Ignition timing:
      8 to 12° BTDC at idle

      HINT:
      Refer to the intelligent tester operator's manual for help when selecting the DATA LIST.

  1. A082779E69
    When not using the intelligent tester:
    Check the ignition timing.

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connection with a wrong terminal can damage the electrical system.
      2. Turn off all electrical systems before connecting the terminals.
      3. Perform this inspection after the cooling fan motor has turned off.

    2. A052004
      Remove the No. 1 engine cover.

    3. Pull out the wire harness as shown in the illustration. Connect the clip of the timing light to the wire harness.

      NOTICE:
      1. Use a timing light which can detect the first signal.
      2. After checking, be sure to tape the wire harness.

    4. Check the ignition timing at idle.

      Ignition timing:
      8 to 12° BTDC at idle

      NOTICE:
      When checking the ignition timing, the transmission should be in neutral.

      HINT:
      After the engine rpm is kept at 1,000 to 1,300 rpm for 5 seconds, check that it returns to idle speed.

    5. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    6. Check the ignition timing at idle.

      Ignition timing:
      5 to 15° BTDC at idle

    7. Confirm that the ignition timing moves to the advanced angle side when the engine rpm is increased.

    8. Remove the timing light.

    9. Install the No. 1 engine cover.


40. INSPECT ENGINE IDLE SPEED

  1. C139987E06
    Warm up the engine.

  1. When using the intelligent tester:
    Check the idle speed.

    1. Connect the intelligent tester to the DLC3.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    2. Enter DATA LIST MODE on the intelligent tester.

      Idle speed:
      Item
      Specified Condition
      Manual transmission
      850 to 950 rpm
      Automatic transmission
      610 to 710 rpm

      NOTICE:
      1. When checking the idle speed, the transmission should be in neutral.
      2. Check the idle speed with the cooling fan off.
      3. Switch off all accessories and air conditioning before connecting the intelligent tester.

  1. A082779E70
    When not using the intelligent tester:
    Check the idle speed.

    1. Using SST, connect the tachometer tester probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

    2. Check the idle speed.

      Idle speed:
      Item
      Specified Condition
      Manual transmission
      850 to 950 rpm
      Automatic transmission
      610 to 710 rpm


41. INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Disconnect the injector connectors.

  1. Remove the ignition coils.

  1. Remove the spark plugs.

  1. A001037
    Check the cylinder compression pressure.

    1. Insert a compression gauge into the spark plug hole.

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Compression pressure:
      1360 KPa (13.9 kgf/cm2, 198 psi)

      Minimum pressure:
      980 KPa (10 kgf/cm2, 142 psi)

      Difference between each cylinder:
      100 kPa (1.0 kgf/cm2, 14 psi)

      NOTICE:
      1. Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
      2. Check the other cylinders' compression pressure in the same way.
      3. This measurement must be done as quickly as possible.

    4. If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect again.

      HINT:
      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      2. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.


42. INSPECT CO/HC
  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe during idling.

  1. Immediately check CO/HC concentration at idle and/at 2,500 rpm.

    HINT:
    1. Complete the measurement within 3 minutes.
    2. Check regulations and restrictions in your area when performing 2 mode CO/HC concentration testing (engine check at both idle speed and at 2,500 rpm).

  1. If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.

    1. Check A/F sensor operation (Click here).

    2. Check heated oxygen sensor operation (Click here).

    3. See the table below for possible causes, and then inspect and repair.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignition:
        1. Incorrect timing
        2. Fouled, shorted, or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaking intake or exhaust valves
      4. Compression leaks from cylinders
      Low
      High
      Rough idle
      (fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective engine coolant temperature sensor
        3. Defective MAF meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor


43. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A134904
    Install the engine cover with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


44. INSTALL FRONT FENDER APRON SEAL RH

45. INSTALL ENGINE UNDER COVER LH

46. INSTALL ENGINE UNDER COVER RH

47. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }

← INSTALLATION (Jun 2006 – Sep 2006)INSTALLATION (from Jun 2009) →