2006-2011 Camry Aurion · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


INSPECT STARTER ASSEMBLY

CAUTION:
Make sure to complete each of the following tests within 5 seconds to prevent the coil from burning out.

  1. Perform pull-in test:

    1. A133511E01
      Disconnect the lead wire from terminal C.

    2. A133512E01
      Connect the battery to the magnetic switch as shown in the illustration. Check that the clutch pinion gear moves outward.
      If the clutch pinion gear does not move outward, replace the repair service starter kit.

  1. Perform hold-in test:

    1. A133513E01
      Disconnect the negative (-) terminal lead from terminal C under the conditions for pull-in test. Check that the pinion gear remains out.
      If the clutch pinion gear moves inward, replace the repair service starter kit.

  1. Inspect clutch pinion gear return:

    1. A133514E01
      Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear moves inward.
      If the clutch pinion gear does not move inward, replace the repair service starter kit.

  1. Perform no-load performance test:

    1. Connect the field coil wire to terminal C with the nut. Make sure that the lead is not grounded.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    2. Clamp the starter in a vise.

    3. A133510E01
      Connect the battery and an ammeter to the starter as shown in the illustration.

    4. Check that the starter rotates smoothly and steadily with the clutch pinion gear extended. Check that the ammeter reads the specified current.

      Standard current:
      Condition
      Specified Condition
      11.5 V
      90 A or less

      If the result is not as specified, overhaul the starter assembly.


INSPECT REPAIR SERVICE STARTER KIT

  1. Check the plunger.

    1. A058586E04
      Push in the plunger and check that it returns quickly to its original position.
      If necessary, replace the repair service starter kit.

  1. Inspect the resistance of the pull-in coil.

    1. A079725E08
      Using an ohmmeter, measure the resistance between terminals 50 and C.

      Standard resistance:
      Tester Connection
      Specified Condition
      Terminal 50 - Terminal C
      Below 1 Ω

      If the resistance is not as specified, replace the repair service starter kit.

  1. Inspect the resistance of the hold-in coil.

    1. A079726E07
      Using an ohmmeter, measure the resistance between terminal 50 and switch body.

      Standard resistance:
      Tester Connection
      Specified Condition
      Terminal 50 - Switch body
      Below 2 Ω

      If the resistance is not as specified, replace the repair service starter kit.


INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the commutator surface for dirt or burning.
    If the surface is dirty or burnt, smooth the surface with 400-grit sandpaper or leather.

  1. Inspect the resistance of the commutator.

    1. A058372E04
      Using an ohmmeter, measure the resistance between the segments of the commutator.

      Standard resistance:
      Tester Connection
      Specified Condition
      Segment - Segment
      Below 1 Ω

      If the resistance is not as specified, replace the starter armature assembly.

    2. A058373E04
      Using an ohmmeter, measure the resistance between the commutator and armature coil core.

      Standard resistance:
      Tester Connection
      Specified Condition
      Commutator - Armature coil core
      10 kΩ or higher

      If the resistance is not as specified, replace the starter armature assembly.

  1. A058584E09
    Using vernier calipers, measure the commutator depth.

    Specified depth:
    3.1 mm (0.122 in.)

    Maximum depth:
    3.8 mm (0.150 in.)

    If the depth is greater than the maximum, replace the starter armature assembly.


INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY

  1. Check the brush length.

    1. A076677E10
      Using vernier calipers, measure the brush length.

      Specified length:
      9.0 mm (0.354 in.)

      Maximum length:
      4.0 mm (0.157 in.)

      If the length is less than the minimum, replace the starter commutator end frame assembly.

  1. Check the resistance.

    1. A079766E10
      Using an ohmmeter, measure the resistance between the positive (+) and negative (-) brushes.

      Resistance:
      10 kΩ or higher

      If the resistance is not as specified, repair or replace the starter commutator end frame assembly.


INSPECT MOTOR TERMINAL STARTER KIT

  1. Check the starter clutch.

    1. A081655E05
      Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.
      If necessary, replace the motor terminal starter kit.

← DISASSEMBLY (from Jun 2009)INSPECTION (from Jun 2009) →