2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Interior Light Circuit

Circuit diagnosis · Vehicles built from Oct 2006

DESCRIPTION

The main body ECU controls the illuminated entry system (interior light and ignition key cylinder light).

WIRING DIAGRAM

E121492E11

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select the item(s) below in the ACTIVE TEST, and check the operation.

    Main Body (Main Body ECU): 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Illuminated Entry System
    Interior light and ignition key cylinder light (Interior light switch is in DOOR position and all doors are closed).
    ON / OFF
    -

OK:
Each light illuminates.



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2. CHECK VEHICLE CONDITION
  1. Check the vehicle condition.

    Result:
    Condition
    Proceed to
    without Sliding Roof
    A
    with Sliding Roof
    B



B
Go to step 4
A


3. CHECK HARNESS AND CONNECTOR (LIGHT - BATTERY AND INSTRUMENT PANEL J/B ASSEMBLY)

  1. E121508E04
    Disconnect the E25 transponder key amplifier connector (*1).

  1. Disconnect the Q9 rear room light assembly connector.

  1. Disconnect the IR and II instrument panel J/B assembly connectors.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E25-2 (ILL+) - Body ground (*1)
    Always
    10 to 14 V
    Q9-1 (B) - Body ground
    Always
    10 to 14 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    II-10 - E25-6 (ILL-) (*1)
    Always
    Below 1 Ω
    IR-5 - Q9-2 (CTY)
    Always
    Below 1 Ω
    II-10 - Body ground
    Always
    10 kΩ or higher
    IR-5 - Body ground
    Always
    10 kΩ or higher

    HINT:
    *1: without Smart Entry and Start System



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4. CHECK HARNESS AND CONNECTOR (LIGHT - BATTERY AND INSTRUMENT PANEL J/B ASSEMBLY)

  1. E121509E04
    Disconnect the E25 transponder key amplifier connector (*1).

  1. Disconnect the Q6 overhead J/B connector.

  1. Disconnect the IR and II instrument panel J/B assembly connectors.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E25-2 (ILL+) - Body ground (*1)
    Always
    10 to 14 V
    Q6-7 (B) - Body ground
    Always
    10 to 14 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    II-10 - E25-6 (ILL-) (*1)
    Always
    Below 1 Ω
    IR-5 - Q6-6 (CTY)
    Always
    Below 1 Ω
    II-10 - Body ground
    Always
    10 kΩ or higher
    IR-5 - Body ground
    Always
    10 kΩ or higher

    HINT:
    *1: without Smart Entry and Start System



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


← Door LOCK Position Circuit (from Jun 2009)Engine Switch Illumination Circuit (from Oct 2006) →