2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Image from Camera for Rear View Monitor is Abnormal

Circuit diagnosis · Vehicles built from Jun 2009

DESCRIPTION

The display signal from the rear television camera assembly transmits to the radio and display assembly.

WIRING DIAGRAM

E188916E01

INSPECTION PROCEDURE


1. CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Result
    Proceed to
    for 2AZ-FE
    A
    for 2GR-FE
    B



B
Go to step 5
A


2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY - REAR TELEVISION CAMERA)
  1. Disconnect the F8 connector from the radio and display assembly and the S22 connector from the rear television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S22-6 (CV+) - F8-11 (V+)
    Always
    Below 1 Ω
    S22-5 (CB+) - F8-13 (CA+)
    Always
    Below 1 Ω
    S22-1 (CGND) - F8-14 (CGND)
    Always
    Below 1 Ω
    S22-2 (CV-) - F8-12 (V-)
    Always
    Below 1 Ω
    S22-6 (CV+) - Body ground
    Always
    10 kΩ or higher
    S22-5 (CB+) - Body ground
    Always
    10 kΩ or higher
    S22-1 (CGND) - Body ground
    Always
    10 kΩ or higher
    S22-2 (CV-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY - REAR TELEVISION CAMERA)
OK


3. INSPECT RADIO AND DISPLAY ASSEMBLY
  1. Reconnect the S22 connector to the rear television camera assembly.

  1. E188917E01
    Reconnect the F8 connector to the radio and display assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F8-12 (V-) - Body ground
    Always
    Below 1 Ω
    F8-14 (CGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F8-13 (CA+) - F8-14 (CGND)
    Ignition switch on (IG)
    Shift lever in R
    5.5 to 7.0 V

    Text in Illustration 
    *1
    Component with harness connected
    (Radio and Display Assembly)



NG
REPLACE RADIO AND DISPLAY ASSEMBLY (except 2GR-FE RHD) (Click here)
OK


4. INSPECT REAR TELEVISION CAMERA ASSEMBLY

  1. E188918E01
    Check that the F6 and F8 connectors are connected to the radio and display assembly.

  1. E171712E02
    Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display assembly with the connector connected.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    F8-11 (V+) - F6-7 (GND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch on (IG), shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *1
    Component with harness connected
    (Radio and Display Assembly)
    *2
    Waveform 1 (under normal conditions)
    *3
    Waveform 2 (camera lens is covered, blacking out the screen)
    *4
    Synchronized Signal
    *5
    Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (for 2AZ-FE) (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY - REAR TELEVISION CAMERA)
  1. Disconnect the F8 connector from the radio and display assembly.

  1. Disconnect the S17 connector from the rear television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S17-2 (CV+) - F8-11 (V+)
    Always
    Below 1 Ω
    S17-4 (CB+) - F8-13 (CA+)
    Always
    Below 1 Ω
    S17-3 (CGND) - F8-14 (CGND)
    Always
    Below 1 Ω
    S17-1 (CV-) - F8-12 (V-)
    Always
    Below 1 Ω
    S17-2 (CV+) - Body ground
    Always
    10 kΩ or higher
    S17-4 (CB+) - Body ground
    Always
    10 kΩ or higher
    S17-3 (CGND) - Body ground
    Always
    10 kΩ or higher
    S17-1 (CV-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY - REAR TELEVISION CAMERA)
OK


6. INSPECT RADIO AND DISPLAY ASSEMBLY
  1. Reconnect the S17 connector to the rear television camera assembly.

  1. E188917E01
    Reconnect the F8 connector to the radio and display assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F8-12 (V-) - Body ground
    Always
    Below 1 Ω
    F8-14 (CGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F8-13 (CA+) - F8-14 (CGND)
    Ignition switch on (IG)
    Shift lever in R
    5.5 to 7.0 V

    Text in Illustration 
    *1
    Component with harness connected
    (Radio and Display Assembly)



NG
REPLACE RADIO AND DISPLAY ASSEMBLY (for 2GR-FE RHD) (Click here)
OK


7. INSPECT REAR TELEVISION CAMERA ASSEMBLY

  1. E188918E01
    Check that the F6 and F8 connectors are connected to the radio and display assembly.

  1. E171712E02
    Check the waveform of the rear television camera assembly using an oscilloscope.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    F8-11 (V+) - F6-7 (GND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch on (IG), shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *1
    Component with harness connected
    (Radio and Display Assembly)
    *2
    Waveform 1 (under normal conditions)
    *3
    Waveform 2 (camera lens is covered, blacking out the screen)
    *4
    Synchronized Signal
    *5
    Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (for 2GR-FE) (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Reverse Signal Circuit (from Jun 2009)COMPONENTS (from Oct 2006) →