2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

Open in One Side of CAN Branch Line

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "Communication Bus Check" screen, one side of the CAN branch wire may be open. (One side of the CAN-H [branch wire] / CAN-L [branch wire] of the ECU and/or sensor is open.)
Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "Communication Bus Check" screen.
  1. One side of the CAN branch wire is open
  2. Steering angle sensor
  3. Skid control ECU
  4. ECM
  5. Yaw rate sensor
  6. Main body ECU
  7. Air conditioning amplifier
  8. Center airbag sensor
  9. Combination meter
  10. Navigation receiver assembly

WIRING DIAGRAM

C213910E04
C225793E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any other switches, or any doors triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


1. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE
  1. Confirm the systems (ECUs and sensors), which use CAN communication, equipped on the vehicle. (Click here)

  1. Using the intelligent tester, select and perform "Bus Check". (Click here) [*1]

  1. Observe the screen for approximately 1 minute to check the ECUs and sensors that are not displayed on the screen and also those that repeatedly appear and disappear from the screen.

  1. Disconnect the branch wire connectors, which are connected to the ECUs or sensors that are not displayed on the screen, from the CAN J/C.C212233E01

  1. CAN No. 1 J/CC142744E05

    CAN No. 1 J/C connectors ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    CAN Main Bus Wire (E42)
    White
    B
    W
    Center Airbag Sensor Assembly (E45)
    Black
    B
    W
    CAN No. 1 J/C connectors ("B" side, without earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Yaw Rate Sensor (E46)
    Blue
    B
    W
    Air Conditioning Amplifier (E47)
    Gray
    B
    W
    Navigation Receiver Assembly (E93)*
    Brown
    B
    W
    Combination Meter (E43)
    White
    B
    W
    Main Body ECU (E44)
    Black
    B
    W
    *: w/ Navigation system

  1. CAN No. 4 J/C (REAR OF THE VEHICLE) C137762E08

    Terminals
    Wiring Color
    Connects to
    A40-1 (CANH)
    B
    ECM (CANH)
    A40-7 (CANL)
    W
    ECM (CANL)
    A40-2 (CANH)
    B
    Skid Control ECU (CANH)
    A40-8 (CANL)
    W
    Skid Control ECU (CANL)

  1. CAN No. 4 J/C (FRONT OF THE VEHICLE)C137763E50

    Terminals
    Wiring Color
    Connects to
    E41-2 (CANH)
    B
    DLC3 (CANH)
    E41-8 (CANL)
    W
    DLC3 (CANL)
    E41-4 (CANH)
    B
    CAN No. 1 J/C (CANH)
    E41-10 (CANL)
    W
    CAN No. 1 J/C (CANL)
    E41-3 (CANH)
    B
    Steering Angle Sensor (CANH)
    E41-9 (CANL)
    W
    Steering Angle Sensor (CANL)

    HINT:
    1. Connecting locations of the connectors shown in the above tables are those of a vehicle whose connector locations have never been changed.
    2. If the connector locations differ from those shown in the above tables, identify each connector according to the color of the bus wires.

  1. Check that the ECUs and sensors, which repeatedly appeared and disappeared from the "Bus Check" screen, are constantly displayed.

  1. Perform the communication stop mode check for the ECUs and sensors which correspond to the disconnected branch wire connectors.


NEXT

GO TO CORRESPONDING COMMUNICATION STOP MODE


← Open in One Side of CAN Branch Line (Oct 2006 – May 2009)COMPONENTS (from Oct 2006) →