Open in One Side of CAN Branch Line
Circuit diagnosis · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
If some ECUs and sensors are not displayed on the "Communication Bus Check" screen of the intelligent tester and some ECUs and sensors repeatedly appear and disappear from the screen when the CAN main bus wires are normal (there is no open, short, short to B+, or short to GND in the main bus wires), there may be an open circuit in either of the CAN branch wires.- HINT:
- If some ECUs and sensors repeatedly appear and disappear from the "Communication Bus Check" screen, communication between the normal ECUs (sensors) and intelligent tester may be affected by the incomplete signals that are output from the ECU that has an open circuit in either of its CAN branch wires. In this case, the CAN branch wires for the ECUs and sensors that repeatedly appear and disappear from the screen are normal and the ECU that is not displayed on the screen may be the main cause of the problem (this ECU may have an open circuit in either of its CAN branch wires).
| Symptom |
Trouble Area |
| 2 or more ECUs and/or sensors do not appear on the intelligent tester "Communication Bus Check" screen. |
One side of the CAN branch wire is open
|
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK FOR OPEN IN ONE SIDE OF CAN NO. 1 BUS BRANCH WIRE |
Confirm the systems (ECUs and sensors), which use CAN communication, equipped on the vehicle. (Click here)
Using the intelligent tester, select and perform "Bus Check". (Click here)
Observe the screen for approximately 1 minute to check the ECUs and sensors that are not displayed on the screen and also those that repeatedly appear and disappear from the screen.
Disconnect the branch wire connectors, which are connected to the ECUs or sensors that are not displayed on the screen, from the CAN J/C.




CAN No. 1 J/C Connector ("A" side, with earth terminal)
Connector Color
Color (CAN-H Side)
Color (CAN-L Side)
CAN No. 1 Bus Main Wire (E42)
White
B
W
Center Airbag Sensor Assembly (E45)
Black
B
W
CAN No. 1 J/C Connector ("B" side, without earth terminal)
Connector Color
Color (CAN-H Side)
Color (CAN-L Side)
Yaw Rate Sensor (E46)
Blue
B
W
Air Conditioning Amplifier (E47)
Gray
B
W
Navigation Receiver Assembly (E93)
Brown
B
W
Combination Meter (E43)
White
B
W
Main Body ECU (E44)
Black
B
W
CAN No. 4 J/C (REAR OF THE VEHICLE)


Wiring color: Terminal
Wiring Color
Destination
A40-1 (CANH)
B
ECM (CANH)
A40-7 (CANL)
W
ECM (CANL)
A40-2 (CANH)
B
Skid Control ECU (CANH)
A40-8 (CANL)
W
Skid Control ECU (CANL)
CAN No. 4 J/C (FRONT OF THE VEHICLE)


*: w/ AFSWiring color: Terminals
Wiring Color
Destination
E41-1 (CANH)
B
Gateway ECU (CANH) *
E41-7 (CANL)
W
Gateway ECU (CANL) *
E41-2 (CANH)
B
DLC3 (CANH)
E41-8 (CANL)
W
DLC3 (CANL)
E41-3 (CANH)
B
Steering Angle Sensor (CANH)
E41-9 (CANL)
W
Steering Angle Sensor (CANL)
E41-4 (CANH)
B
CAN No. 1 J/C (CANH)
E41-10 (CANL)
W
CAN No. 1 J/C (CANL)
- HINT:
- Connecting locations of the connectors shown in the above tables are those of a vehicle whose connector locations have never been changed.
- If the connector locations differ from those shown in the above tables, identify each connector according to the color of the bus wires.
- Connecting locations of the connectors shown in the above tables are those of a vehicle whose connector locations have never been changed.
Check that the ECUs and sensors, which repeatedly appeared and disappeared from the "Bus Check" screen, are constantly displayed.
Perform the communication stop mode check for the ECUs and sensors which correspond to the disconnected branch wire connectors.
| NEXT | ||
| ||
