2006-2011 Camry Aurion · Service Manual ENGINE

Power Source Mode does not Change to ON (IG and ACC)

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

When the engine switch is pushed with the electrical key in the cabin, the main body ECU receives signals to switch the power source mode.

HINT:
To allow use of the intelligent tester to inspect the push-button start function when the engine switch is off, repeat opening and closing any of the doors. Opening and closing a door establishes communication between the intelligent tester and the main body ECU. (Opening and closing a door can also be simulated by operating a door courtesy light switch.)


WIRING DIAGRAM

B157550E01
B157551E03

INSPECTION PROCEDURE


1. CHECK ENTRY FUNCTION DETECTION AREA

  1. B137958E01
    Inspect entry detection area.
    1. When the electrical key is in either of the 2 inspection points in the illustration, the shift lever is in the P position and the brake pedal is depressed, check that the engine switch indicator illuminates in green.

      OK:
      Engine switch illuminates in green.

      HINT:
      If the engine switch does not illuminate, perform troubleshooting according to the PROBLEM SYMPTOMS TABLE (Click here).



NG
GO TO OTHER PROBLEM
OK


2. INSPECT FUSE (AM2)
  1. Remove the AM2 fuse from the engine room J/B.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


3. CHECK CONNECTORS
  1. Check that the connectors are securely connected and the terminals are not deformed or loose.

    OK:
    The connectors are securely connected and the terminals are not deformed or loose.



NG
REPAIR OR REPLACE CONNECTORS
OK


4. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)

  1. B138000E13
    Disconnect the E6 and E7 ECU connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E7-6 (AM1) - Body ground
    Always
    11 to 14 V
    E6-1 (AM2) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)

  1. B157557E01
    Disconnect the IF and IM ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IF-10 (GND1) - Body ground
    Always
    Below 1 Ω
    IM-9 (GND2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK FOR DTCS
  1. Delete the DTCs (Click here).

    HINT:
    After all the DTCs are cleared, check if the trouble occurs again 5 seconds after the engine switch is turned on (IG).

  1. Check for DTCs again.

    OK:
    No DTC is output.



NG
GO TO DTC CHART
OK


7. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Check the DATA LIST for proper functioning of the start switches 1 and 2.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    St SW1
    Start Switch 1/ON or OFF
    ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    -
    St SW2
    Start Switch 2/ON or OFF
    ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    -

    OK:
    ON (engine switch is pushed) and OFF (engine switch is not pushed) appear on the screen.



NG
Go to step 8
OK

REPLACE MAIN BODY ECU

8. INSPECT ENGINE SWITCH

  1. Remove the engine switch.A109252E18

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Pushed
    Below 1 Ω
    7 (SS1) - 5 (GND)
    Not pushed
    10 kΩ or higher
    2 (SS2) - 5 (GND)
    Not pushed
    10 kΩ or higher



NG
REPLACE ENGINE SWITCH (Click here)
OK


9. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU AND BODY GROUND - ENGINE SWITCH)

  1. Disconnect the E7 ECU connector.B137980E14

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E52-7 (SS1) - E7-17 (SSW1)
    Always
    Below 1 Ω
    E52-2 (SS2) - E7-16 (SSW2)
    Always
    Below 1 Ω
    E52-5 (GND) - Body ground
    Always
    Below 1 Ω
    E52-7 (SS1) or E7-17 (SSW1) - Body ground
    Always
    10 kΩ or higher
    E52-2 (SS2) or E7-16 (SSW2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Power Source Mode does not Change to ON (IG and ACC) (Oct 2006 – May 2009)Power Source Mode does not Change to ON (IG) (from Oct 2006) →