TERMINALS OF ECM
System information · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| SFI SYSTEM |
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.


- HINT:
- The standard normal voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated.
- The check results should be compared with the standard normal voltage for that pair of terminals, listed in the "STD Voltages" column.
- The illustration above can be used as a reference to identify the ECM terminal locations.
| Symbols (Terminal No.) |
Wiring Colors |
Terminal Descriptions |
Conditions |
STD Voltages |
| +B (A24-2) - E1 (C58-81) |
R - W-B |
Power source of ECM |
Ignition switch on (IG) |
9 to 14 V |
| +B2 (A24-1) - E1 (C58-81) |
R - W-B |
Power source of ECM |
Ignition switch on (IG) |
9 to 14 V |
| BATT (A24-20) - E1 (C58-81) |
Y - W-B |
Battery (for measuring the battery voltage and for the ECM memory) |
Always |
9 to 14 V |
| +BM (A24-3) - E1 (C58-81) |
LG - W-B |
Power source of ETCS throttle motor |
Always |
9 to 14 V |
| MREL (A24-44) - E1 (C58-81) |
BE - W-B |
EFI relay operation signal |
Ignition switch on (IG) |
9 to 14 V |
| IGSW (A24-28) - E1 (C58-81) |
Y - W-B |
Ignition switch signal |
Ignition switch on (IG) |
9 to 14 V |
| ACCR (A24-13) - E1 (C58-81) |
B - W-B |
ACC relay control signal |
Cranking |
Below 1.5 V |
| FC (A24-7) - E1 (C58-81) |
Y - W-B |
C/OPEN relay operation signal (fuel pump control) |
Ignition switch on (IG) |
9 to 14 V |
| STSW (A24-14) - E1 (C58-81) |
R - W-B |
Engine switch signal |
Shift lever position P or N, engine switch START |
6.0 V or more |
| STP ( A24-36) - E1 (C58-81) |
W - W-B |
Stop light switch signal |
W-Bake pedal depressed |
7.5 to 14 V |
| STP (A24-36) - E1 C58-81) |
W - W-B |
Stop light switch signal |
W-Bake pedal released |
Below 1.5 V |
| ST1- (A24-35) - E1 (C58-81) |
GR - W-B |
Stop light switch signal (opposite to STP terminal) |
Ignition switch on (IG), W-Bake pedal depressed |
Below 1.5 V |
| ST1- (A24-35) - E1 (C58-81) |
GR - W-B |
Stop light switch signal (opposite to STP terminal) |
Ignition switch on (IG), W-Bake pedal released |
7.5 to 14 V |
| VCV1 (C58-115) - E1 (C58-81) |
Y - W-B |
Power source for VVT sensor (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VCV2 (C58-113) - E1 (C58-81) |
R - W-B |
Power source for VVT sensor (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VCE1 (C58-114) - E1 (C58-81) |
R - W-B |
Power source for VVT sensor (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VCE2 (C58-112) - E1 (C58-81) |
LG - W-B |
Power source for VVT sensor (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VPA (A24-55) - E1 (C58-81) |
G - W-B |
Accelerator pedal position sensor signal (for engine control) |
Ignition switch on (IG), Accelerator pedal fully released |
0.5 to 1.1 V |
| VPA (A24-55) - E1 (C58-81) |
G - W-B |
Accelerator pedal position sensor signal (for engine control) |
Ignition switch on (IG), Accelerator pedal fully depressed |
2.6 to 4.5 V |
| VPA2 (A24-56) - EPA2 (A24-60) |
R - BE |
Accelerator pedal position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully released |
1.2 to 2.0 V |
| VPA2 (A24-56) - EPA2 (A24-60) |
R - BE |
Accelerator pedal position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully depressed |
3.4 to 5.0 V |
| EPA (A24-59) - VPA (A24-55) |
Y - G |
Accelerator pedal position sensor signal (for engine control) |
Ignition switch on (IG), Accelerator pedal fully released |
0.5 to 1.1 V |
| EPA (A24-59) - VPA (A24-55) |
Y - G |
Accelerator pedal position sensor signal (for engine control) |
Ignition switch on (IG), Accelerator pedal fully depressed |
2.6 to 4.5 V |
| EPA2 (A24-60) - VPA2 (A24-56) |
BE - R |
Accelerator pedal position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully released |
1.2 to 2.0 V |
| EPA2 (A24-60) - VPA2 (A24-56) |
BE - R |
Accelerator pedal position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully depressed |
3.4 to 5.0 V |
| TC (A24-27) - E1 (C58-81) |
P - W-B |
Terminal TC of DLC3 |
Ignition switch on (IG) |
9 to 14 V |
| VCTA (C58-96) - ETA (C58-97) |
B - P |
Power source for throttle position (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VCPA (A24-57) - EPA (A24-59) |
B - Y |
Power source of accelerator pedal position sensor (for VPA) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VCP2 (A24-58) - EPA2 (A24-60) |
L - BE |
Power source of accelerator pedal position sensor (for VPA2) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| TACH (A24-15) - E1 (C58-81) |
B - W-B |
Engine speed signal (for combination meter) |
Idling |
Pulse generation (see waveform 11) |
| CCS (A24-40) - E1 (C58-81) |
W - W-B |
Cruise control main switch signal |
Ignition switch on (IG) CANCEL switch ON SET/COAST switch ON RES/ACC switch ON Main switch ON |
10 to 16 V 6.6 to 10.1 V 4.5 to 7.1 V 2.3 to 4.0 V Below 1 V |
| SPD (A24-8) - E1 (C58-81) |
V - W-B |
Vehicle speed signal from combination meter |
Ignition switch on (IG), Rotate driving wheel slowly |
Pulse generation (see waveform 8) |
| W (A24-24) - E1 (C58-81) |
BR - W-B |
Malfunction Indicator Lamp (MIL) operation signal |
Ignition switch on (IG) |
Below 3.0 V |
| W (A24-24) - E1 (C58-81) |
BR - W-B |
Malfunction Indicator Lamp (MIL) operation signal |
Idling |
9 to 14 V |
| CANH (A24-41) - E1 (C58-81) |
B - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (see waveform 12) |
| CANL (A24-49) - E1 (C58-81) |
W - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (see waveform 13) |
| E1 (C58-81) - Body ground |
W-B - - |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| #10 (C58-45) - E01 (C58-22) #20 (C58-85) - E01 (C58-22) #30 (C58-44) - E01 (C58-22) #40 (C58-84) - E01 (C58-22) #50 (C58-43) - E01 (C58-22) #60 (C58-83) - E01 (C58-22) |
B - W-B R - W-B Y - W-B L - W-B W-L - W-B BR - W-B |
Fuel injector operation signal |
Ignition switch on (IG) |
9 to 14 V |
| #10 (C58-45) - E01 (C58-22) #20 (C58-85) - E01 (C58-22) #30 (C58-44) - E01 (C58-22) #40 (C58-84) - E01 (C58-22) #50 (C58-43) - E01 (C58-22) #60 (C58-83) - E01 (C58-22) |
B - W-B R - W-B Y - W-B L - W-B W-L - W-B BR - W-B |
Fuel injector operation signal |
Idling |
Pulse generation (see waveform 3) |
| PSW (C58-70) - E1 (C58-81) |
B - W-B |
P/S pressure switch signal |
Ignition switch on (IG) |
9 to 14 V |
| STA (A24-48) - E1 (C58-81) |
V - W-B |
Starter relay operation signal |
Cranking |
9 to 14 V |
| OC2- (C58-51) - OC2+ (C58-52) |
R - BR |
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OC2+ (C58-52) - OC2- (C58-51) |
BR - R |
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OC1- (C58-57) - OC1+ (C58-58) |
B - W |
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OC1+ (C58-58) - OC1- (C58-57) |
W - B |
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| VV2+ (C58-67) - VV2- (C58-90) |
W - B |
Variable Valve Timing (VVT) sensor signal (Intake side) |
Idling |
Pulse generation (see waveform 5) |
| VV2- (C58-90) - VV2+ (C58-67) |
B - W |
Variable Valve Timing (VVT) sensor signal (Intake side) |
Idling |
Pulse generation (see waveform 5) |
| VV1+ (C58-69) - VV1- (C58-92) |
L - LG |
Variable Valve Timing (VVT) sensor signal (Intake side) |
Idling |
Pulse generation (see waveform 5) |
| VV1- (C58-92) - VV1+ (C58-69) |
LG - L |
Variable Valve Timing (VVT) sensor signal (Intake side) |
Idling |
Pulse generation (see waveform 5) |
| NE- (C58-111) - NE+ (C58-110) |
R - G |
Crankshaft position sensor signal |
Idling |
Pulse generation (see waveform 5) |
| NE+ (C58-110) - NE- (C58-111) |
G - R |
Crankshaft position sensor signal |
Idling |
Pulse generation (see waveform 5) |
| EV2- (C58-89) - EV2+ (C58-66) |
L - G-R |
Variable Valve Timing (VVT) sensor signal (Exhaust side) |
Idling |
Pulse generation (see waveform 5) |
| EV2+ (C58-66) - EV2- (C58-89) |
G-R - L |
Variable Valve Timing (VVT) sensor signal (Exhaust side) |
Idling |
Pulse generation (see waveform 5) |
| EV1- (C58-91) - EV1+ (C58-68) |
B - Y |
Variable Valve Timing (VVT) sensor signal (Exhaust side) |
Idling |
Pulse generation (see waveform 5) |
| EV1+ (C58-68) - EV1- (C58-91) |
Y - B |
Variable Valve Timing (VVT) sensor signal (Exhaust side) |
Idling |
Pulse generation (see waveform 5) |
| OE1+ (C58-16) - OE1- (C58-17) |
L - LG |
Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OE1- (C58-17) - OE1+ (C58-16) |
LG - L |
Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OE2+ (C58-14) - OE2- (C58-15) |
W-L - Y |
Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OE2- (C58-15) - OE2+ (C58-14) |
Y - W-L |
Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| HT1B (C58-48) - E1 (C58-81) HT2B (C58-47) - E1 (C58-81) |
LG - W-B Y - W-B |
Heated oxygen sensor heater operation signal |
Idling |
Below 3.0 V |
| HT1B (C58-48) - E1 (C58-81) HT2B (C58-47) - E1 (C58-81) |
LG - W-B Y - W-B |
Heated oxygen sensor heater operation signal |
Ignition switch on (IG) |
9 to 14 V |
| ACM (C58-42) - E1 (C58-81) |
L-B - W-B |
VSV for active control mount system operation signal |
Ignition switch on (IG) |
9 to 14 V |
| M- (C58-18) - ME01 (C58-20) |
R - B |
Throttle drive motor operation signal (negative terminal) |
Idling with warm engine |
Pulse generation (see waveform 10) |
| M+ (C58-19) - ME01 (C58-20) |
G - B |
Throttle drive motor operation signal (positive terminal) |
Idling with warm engine |
Pulse generation (see waveform 9) |
| E02 (C58-21) - Body ground |
B-W - - |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| E01 (C58-22) - Body ground |
W-B - - |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| IGT1 (C58-40) - E1 (C58-81) IGT2 (C58-39) - E1 (C58-81) IGT3 (C58-38) - E1 (C58-81) IGT4 (C58-37) - E1 (C58-81) IGT5 (C58-36) - E1 (C58-81) IGT6 (C58-35) - E1 (C58-81) |
W - W-B G-R - W-B G - W-B LG - W-B P - W-B L-B - W-B |
Ignition coil with igniter (ignition signal) |
Idling |
Pulse generation (see waveform 6) |
| GE01 (C58-41) - E1 (C58-81) |
G-R - W-B |
Shielded earth (ground) circuit of throttle drive motor |
Always |
Below 1 V |
| OX1B (C58-88) - EX1B (C58-65) OX2B (C58-87) - EX2B (C58-64) |
W - BR B - W-B |
Heated oxygen sensor signal |
With engine speed at 2,500 rpm for 2 minutes after warming up |
Pulse generation (see waveform 2) |
| VTA2 (C58-99) - ETA (C58-97) |
W-L - P |
Throttle position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully released |
2.1 to 3.1 V |
| VTA2 (C58-99) - ETA (C58-97) |
W-L - P |
Throttle position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully depressed |
4.5 to 5.0 V |
| VTA1 (C58-98) - ETA (C58-97) |
Y - P |
Throttle position sensor signal (for engine control) |
Ignition switch on (IG), Throttle valve fully closed |
0.5 to 1.2 V |
| VTA1 (C58-98) - ETA (C58-97) |
Y - P |
Throttle position sensor signal (for engine control) |
Ignition switch on (IG), Throttle valve fully open |
3.2 to 4.8 V |
| THW (C58-79) - ETHW (C58-78) |
B - P |
Engine coolant temperature sensor signal |
Idling, Engine coolant temperature 80°C (176°F) |
0.2 to 1.0 V |
| THA (C58-71) - ETHA (C58-74) |
P - G-R |
Intake air temperature sensor signal |
Idling, Intake air temperature 20°C (68°F) |
0.5 to 3.4 V |
| IGF1 (C58-106) - E1 (C58-81) |
BR - W-B |
Ignition coil with igniter (ignition confirmation signal) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| IGF1 (C58-106) - E1 (C58-81) |
BR - W-B |
Ignition coil with igniter (ignition confirmation signal) |
Idling |
Pulse generation (see waveform 6) |
| AICV (A24-4) - E1 (C58-81) |
V - W-B |
VSV for Air intake control system operation signal |
Ignition switch on (IG) |
9 to 14 V |
| E2G (C58-73) - E1 (C58-81) |
LG - W-B |
Earth (ground) circuit of sensor for mass air flow meter |
Always |
Below 1 V |
| VG (C58-72) - E2G (C58-73) |
L-B - LG |
Mass Air Flow (MAF) meter signal |
Idling, Shift lever position P or N, A/C switch OFF |
0.5 to 3.0 V |
| ACIS (C58-107) - E1 (C58-81) |
B-W - W-B |
VSV for ACIS (Acoustic Control Induction System) operation signal |
Ignition switch on (IG) |
9 to 14 V |
| PRG (C58-108) - E1 (C58-81) |
G-R - W-B |
Purge VSV for EVAP system operation signal |
Ignition switch on (IG) |
9 to 14 V |
| PRG (C58-108) - E1 (C58-81) |
G-R - W-B |
Purge VSV for EVAP system operation signal |
Idling |
Pulse generation (see waveform 7) |
| HA2A (C58-109) - E05 (C58-46) |
B-W - W |
A/F sensor heater operation signal |
Idling |
Below 3.0 V |
| HA2A (C58-109) - E05 (C58-46) |
B-W - W |
A/F sensor heater operation signal |
Ignition switch on (IG) |
9 to 14 V |
| HA1A (C58-86) - E04 (C58-23) |
G - W |
A/F sensor heater operation signal |
Idling |
Below 3.0 V |
| HA1A (C58-86) - E04 (C58-23) |
G - W |
A/F sensor heater operation signal |
Ignition switch on (IG) |
9 to 14 V |
| ME01 (C58-20) - E1 (C58-81) |
B - W-B |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| E03 (C58-104) - E1 (C58-81) |
B - W-B |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| HT2B (C58-47) - E1 (C58-81) HT1B (C58-48) - E1 (C58-81) |
Y - W-B LG - W-B |
Heated oxygen sensor heater operation signal |
Idling |
Below 3.0 V |
| HT2B (C58-47) - E1 (C58-81) HT1B (C58-48) - E1 (C58-81) |
Y - W-B LG - W-B |
Heated oxygen sensor heater operation signal |
Ignition switch on (IG) |
9 to 14 V |
| E05 (C58-46) - E1 (C58-81) |
W - W-B |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| E04 (C58-23) - E1 (C58-81) |
W - W-B |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| NSW (C58-62) - E1 (C55-81) |
L-B - W-B |
Park/Neutral position switch signal |
Ignition switch on (IG), Shift lever position P or N |
Below 3.0 V |
| NSW (C58-62) - E1 (C55-81) |
L-B - W-B |
Park/Neutral position switch signal |
Ignition switch on (IG), Shift lever position P or N |
9 to 14 V |
| EKN2 (C58-117) - KNK2 (C58-118) |
W - B |
Earth (ground) circuit of knock sensor |
With engine speed at 4,000 rpm after warming up |
Pulse generation (see waveform 4) |
| KNK2 (C58-118) - EKN2 (C58-117) |
B - W |
Knock sensor signal |
With engine speed at 4,000 rpm after warming up |
Pulse generation (see waveform 4) |
| A1A+ (C58-93) - E1 (C58-81) |
L - W-B |
A/F sensor signal |
Ignition switch on (IG) |
3.3 V*1
|
| A1A+ (C58-93) - E1 (C58-81) |
L - W-B |
A/F sensor signal |
Ignition switch on (IG) |
3.0 V*1
|
| A2A+ (C58-120) - E1 (C58-81) |
BR - W-B |
A/F sensor signal |
Ignition switch on (IG) |
3.3 V*1
|
| A2A+ (C58-120) - E1 (C58-81) |
BR - W-B |
A/F sensor signal |
Ignition switch on (IG) |
3.0 V*1
|
| EKNK (C58-94) - KNK1 (C58-95) |
G - R |
Earth (ground) circuit of knock sensor |
With engine speed at 4,000 rpm after warming up |
Pulse generation (see waveform 4) |
| KNK1 (C58-95) - EKNK (C58-94) |
R - G |
Knock sensor signal |
With engine speed at 4,000 rpm after warming up |
Pulse generation (see waveform 4) |
| A1A- (C58-116) - E1 (C58-81) |
P - W-B |
A/F sensor |
Ignition switch on (IG) |
3.3 V*1
|
| A1A- (C58-116) - E1 (C58-81) |
P - W-B |
A/F sensor |
Ignition switch on (IG) |
3.0 V*1
|
| A2A- (C58-119) - E1 (C58-81) |
Y - W-B |
A/F sensor |
Ignition switch on (IG) |
3.3 V*1
|
| A2A- (C58-119) - E1 (C58-81) |
Y - W-B |
A/F sensor |
Ignition switch on (IG) |
3.0 V*1
|
| OX2B (C58-87) - EX2B (C58-64) OX1B (C58-88) - EX1B (C58-65) |
B - W-B W - BR |
Heated oxygen sensor signal |
With engine speed at 2,500 rpm for 2 minutes after warming up |
Pulse generation (see waveform 2) |
| P (C58-24) - E1 (C58-81) |
B-W - W-B |
P shift position switch signal |
Ignition switch on (IG) and shift lever P position |
9 to 14 V |
| P (C58-24) - E1 (C58-81) |
B-W - W-B |
P shift position switch signal |
Ignition switch on (IG) and shift lever except P position |
Below 1 V |
| R (C58-25) - E1 (C58-81) |
P - W-B |
R shift position switch signal |
Ignition switch on (IG) and shift lever R position |
9 to 14 V |
| R (C58-25) - E1 (C58-81) |
P - W-B |
R shift position switch signal |
Ignition switch on (IG) and shift lever except R position |
Below 1 V |
| N (C58-27) - E1 (C58-81) |
L-B - W-B |
N shift position switch signal |
Ignition switch on (IG) and shift lever N position |
9 to 14 V |
| N (C58-27) - E1 (C58-81) |
L-B - W-B |
N shift position switch signal |
Ignition switch on (IG) and shift lever except N position |
Below 1 V |
| D (C58-26) - E1 (C58-81) |
G - W-B |
D shift position switch signal |
Ignition switch on (IG) and shift lever D position |
9 to 14 V |
| D (C58-26) - E1 (C58-81) |
G - W-B |
D shift position switch signal |
Ignition switch on (IG) and shift lever except D position |
Below 1 V |
| S (A24-25) - E1 (C58-81) |
Y - W-B |
S shift position switch signal |
Ignition switch on (IG) and shift lever S position |
9 to 14 V |
| S (A24-25) - E1 (C58-81) |
Y - W-B |
S shift position switch signal |
Ignition switch on (IG) and shift lever except S position |
Below 1 V |
| SFTD (A24-51) - E1 (C58-81) |
L - W-B |
Down shift switch signal |
Ignition switch on (IG) and shift lever S position |
9 to 14 V |
| SFTD (A24-51) - E1 (C58-81) |
L - W-B |
Down shift switch signal |
Ignition switch on (IG) and shift lever "-" position (Down shift) |
Below 1 V |
| SFTU (A24-16) - E1 (C58-81) |
R - W-B |
Up shift switch signal |
Ignition switch on (IG) and shift lever S position |
9 to 14 V |
| SFTU (A24-16) - E1 (C58-81) |
R - W-B |
Up shift switch signal |
Ignition switch on (IG) and shift lever "+" position (Up shift) |
Below 1 V |
| CAN+ (C58-2) - E1 (C58-81) |
B - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (see waveform 12) |
| CAN- (C58-1) - E1 (C58-81) |
Y - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (see waveform 13) |
| Symbols (Terminal No.) |
Wiring Colors |
Terminal Descriptions |
Conditions |
STD Voltages |
| +B (A55-2) - E1 (C55-81) |
R - W-B |
Power source of ECM |
Ignition switch on (IG) |
9 to 14 V |
| +B2 (A55-1) - E1 (C55-81) |
R - W-B |
Power source of ECM |
Ignition switch on (IG) |
9 to 14 V |
| BATT (A55-20) - E1 (C55-81) |
Y - W-B |
Battery (for measuring the battery voltage and for the ECM memory) |
Always |
9 to 14 V |
| +BM (A55-3) - E1 (C55-81) |
LG - W-B |
Power source of ETCS throttle motor |
Always |
9 to 14 V |
| MREL (A55-44) - E1 (C55-81) |
BE - W-B |
EFI relay operation signal |
Ignition switch on (IG) |
9 to 14 V |
| IGSW (A55-28) - E1 (C55-81) |
Y - W-B |
Ignition switch signal |
Ignition switch on (IG) |
9 to 14 V |
| ACCR (A55-13) - E1 (C55-81) |
B - W-B |
ACC relay control signal |
Cranking |
Below 1.5 V |
| FC (A55-7) - E1 (C55-81) |
Y - W-B |
C/OPEN relay operation signal (fuel pump control) |
Ignition switch on (IG) |
9 to 14 V |
| STSW (A55-14) - E1 (C55-81) |
R - W-B |
Engine switch signal |
Shift lever position P or N, engine switch START |
6.0 V or more |
| STP ( A55-36 ) - E1 (C55-81) |
W - W-B |
Stop light switch signal |
Brake pedal depressed |
7.5 to 14 V |
| STP (A55-36) - E1 (C55-81) |
W - W-B |
Stop light switch signal |
Brake pedal released |
Below 1.5 V |
| ST1- (A55-35) - E1 (C55-81) |
GR - W-B |
Stop light switch signal (opposite to STP terminal) |
Ignition switch on (IG), Brake pedal depressed |
Below 1.5 V |
| ST1- (A55-35) - E1 (C55-81) |
GR - W-B |
Stop light switch signal (opposite to STP terminal) |
Ignition switch on (IG), Brake pedal released |
7.5 to 14 V |
| VCV1 (C55-115) - E1 (C55-81) |
Y - W-B |
Power source for VVT sensor (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VCV2 (C55-113) - E1 (C55-81) |
R - W-B |
Power source for VVT sensor (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VCE1 (C55-114) - E1 (C55-81) |
R - W-B |
Power source for VVT sensor (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VCE2 (C55-112) - E1 (C55-81) |
LG - W-B |
Power source for VVT sensor (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VPA (A55-55) - E1 (C55-81) |
G - W-B |
Accelerator pedal position sensor signal (for engine control) |
Ignition switch on (IG), Accelerator pedal fully released |
0.5 to 1.1 V |
| VPA (A55-55) - E1 (C55-81) |
G - W-B |
Accelerator pedal position sensor signal (for engine control) |
Ignition switch on (IG), Accelerator pedal fully depressed |
2.6 to 4.5 V |
| VPA2 (A55-56) - EPA2 (A55-60) |
R - BE |
Accelerator pedal position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully released |
1.2 to 2.0 V |
| VPA2 (A55-56) - EPA2 (A55-60) |
R - BE |
Accelerator pedal position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully depressed |
3.4 to 5.0 V |
| EPA (A55-59) - VPA (A55-55) |
Y - G |
Accelerator pedal position sensor signal (for engine control) |
Ignition switch on (IG), Accelerator pedal fully released |
0.5 to 1.1 V |
| EPA (A55-59) - VPA (A55-55) |
Y - G |
Accelerator pedal position sensor signal (for engine control) |
Ignition switch on (IG), Accelerator pedal fully depressed |
2.6 to 4.5 V |
| EPA2 (A55-60) - VPA2 (A55-56) |
BE - R |
Accelerator pedal position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully released |
1.2 to 2.0 V |
| EPA2 (A55-60) - VPA2 (A55-56) |
BE - R |
Accelerator pedal position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully depressed |
3.4 to 5.0 V |
| TC (A55-27) - E1 (C55-81) |
P - W-B |
Terminal TC of DLC3 |
Ignition switch on (IG) |
9 to 14 V |
| VCTA (C55-96) - ETA (C55-97) |
B - P |
Power source for throttle position (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VCPA (A55-57) - EPA (A55-59) |
B - Y |
Power source of accelerator pedal position sensor (for VPA) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| VCP2 (A55-58) - EPA2 (A55-60) |
L - BE |
Power source of accelerator pedal position sensor (for VPA2) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| TACH (A55-15) - E1 (C55-81) |
B - W-B |
Engine speed signal (for combination meter) |
Idling |
Pulse generation (see waveform 11) |
| CCS (A55-40) - E1 (C55-81) |
W - W-B |
Cruise control main switch signal |
Ignition switch on (IG) CANCEL switch ON SET/COAST switch ON RES/ACC switch ON Main switch ON |
10 to 16 V 6.6 to 10.1 V 4.5 to 7.1 V 2.3 to 4.0 V Below 1 V |
| SPD (A55-8) - E1 (C55-81) |
V - W-B |
Vehicle speed signal from combination meter |
Ignition switch on (IG), Rotate driving wheel slowly |
Pulse generation (see waveform 8) |
| W (A55-24) - E1 (C55-81) |
BR - W-B |
Malfunction Indicator Lamp (MIL) operation signal |
Ignition switch on (IG) |
Below 3.0 V |
| W (A55-24) - E1 (C55-81) |
BR - W-B |
Malfunction Indicator Lamp (MIL) operation signal |
Idling |
9 to 14 V |
| CANH (A55-41) - E1 (C55-81) |
B - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (see waveform 12) |
| CANL (A55-49) - E1 (C55-81) |
W - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (see waveform 13) |
| E1 (C55-81) - Body ground |
W-B - - |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| #10 (C55-45) - E01 (C55-22) #20 (C55-85) - E01 (C55-22) #30 (C55-44) - E01 (C55-22) #40 (C55-84) - E01 (C55-22) #50 (C55-43) - E01 (C55-22) #60 (C55-83) - E01 (C55-22) |
B - W-B R - W-B Y - W-B L - W-B W-L - W-B BR - W-B |
Fuel injector operation signal |
Ignition switch on (IG) |
9 to 14 V |
| #10 (C55-45) - E01 (C55-22) #20 (C55-85) - E01 (C55-22) #30 (C55-44) - E01 (C55-22) #40 (C55-84) - E01 (C55-22) #50 (C55-43) - E01 (C55-22) #60 (C55-83) - E01 (C55-22) |
B - W-B R - W-B Y - W-B L - W-B W-L - W-B BR - W-B |
Fuel injector operation signal |
Idling |
Pulse generation (see waveform 3) |
| PSW (C55-70) - E1 (C55-81) |
B - W-B |
P/S pressure switch signal |
Ignition switch on (IG) |
9 to 14 V |
| STA (A55-48) - E1 (C55-81) |
V - W-B |
Starter relay operation signal |
Cranking |
9 to 14 V |
| OC2- (C55-51) - OC2+ (C55-52) |
R - BR |
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OC2+ (C55-52) - OC2- (C55-51) |
BR - R |
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OC1- (C55-57) - OC1+ (C55-58) |
B - W |
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OC1+ (C55-58) - OC1- (C55-57) |
W - B |
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| VV2+ (C55-67) - VV2- (C55-90) |
W - B |
Variable Valve Timing (VVT) sensor signal (Intake side) |
Idling |
Pulse generation (see waveform 5) |
| VV2- (C55-90) - VV2+ (C55-67) |
B - W |
Variable Valve Timing (VVT) sensor signal (Intake side) |
Idling |
Pulse generation (see waveform 5) |
| VV1+ (C55-69) - VV1- (C55-92) |
L - LG |
Variable Valve Timing (VVT) sensor signal (Intake side) |
Idling |
Pulse generation (see waveform 5) |
| VV1- (C55-92) - VV1+ (C55-69) |
LG - L |
Variable Valve Timing (VVT) sensor signal (Intake side) |
Idling |
Pulse generation (see waveform 5) |
| NE- (C55-111) - NE+ (C55-110) |
R - G |
Crankshaft position sensor signal |
Idling |
Pulse generation (see waveform 5) |
| NE+ (C55-110) - NE- (C55-111) |
G - R |
Crankshaft position sensor signal |
Idling |
Pulse generation (see waveform 5) |
| EV2- (C55-89) - EV2+ (C55-66) |
L - G-R |
Variable Valve Timing (VVT) sensor signal (Exhaust side) |
Idling |
Pulse generation (see waveform 5) |
| EV2+ (C55-66) - EV2- (C55-89) |
G-R - L |
Variable Valve Timing (VVT) sensor signal (Exhaust side) |
Idling |
Pulse generation (see waveform 5) |
| EV1- (C55-91) - EV1+ (C55-68) |
B - Y |
Variable Valve Timing (VVT) sensor signal (Exhaust side) |
Idling |
Pulse generation (see waveform 5) |
| EV1+ (C55-68) - EV1- (C55-91) |
Y - B |
Variable Valve Timing (VVT) sensor signal (Exhaust side) |
Idling |
Pulse generation (see waveform 5) |
| OE1+ (C55-16) - OE1- (C55-17) |
L - LG |
Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OE1- (C55-17) - OE1+ (C55-16) |
LG - L |
Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OE2+ (C55-14) - OE2- (C55-15) |
W-L - Y |
Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| OE2- (C55-15) - OE2+ (C55-14) |
Y - W-L |
Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) |
Ignition switch on (IG) |
Pulse generation (see waveform 1) |
| HT1B (C55-48) - E1 (C55-81) HT2B (C55-47) - E1 (C55-81) |
LG - W-B Y - W-B |
Heated oxygen sensor heater operation signal |
Idling |
Below 3.0 V |
| HT1B (C55-48) - E1 (C55-81) HT2B (C55-47) - E1 (C55-81) |
LG - W-B Y - W-B |
Heated oxygen sensor heater operation signal |
Ignition switch on (IG) |
9 to 14 V |
| ACM (C55-42) - E1 (C55-81) |
L-B - W-B |
VSV for active control mount system operation signal |
Ignition switch on (IG) |
9 to 14 V |
| M- (C55-18) - ME01 (C55-20) |
R - B |
Throttle drive motor operation signal (negative terminal) |
Idling with warm engine |
Pulse generation (see waveform 10) |
| M+ (C55-19) - ME01 (C55-20) |
G - B |
Throttle drive motor operation signal (positive terminal) |
Idling with warm engine |
Pulse generation (see waveform 9) |
| E02 (C55-21) - Body ground |
B-W - - |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| E01 (C55-22) - Body ground |
W-B - - |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| IGT1 (C55-40) - E1 (C55-81) IGT2 (C55-39) - E1 (C55-81) IGT3 (C55-38) - E1 (C55-81) IGT4 (C55-37) - E1 (C55-81) IGT5 (C55-36) - E1 (C55-81) IGT6 (C55-35) - E1 (C55-81) |
W - W-B G-R - W-B G - W-B LG - W-B P - W-B L-B - W-B |
Ignition coil with igniter (ignition signal) |
Idling |
Pulse generation (see waveform 6) |
| GE01 (C55-41) - E1 (C55-81) |
G-R - W-B |
Shielded earth (ground) circuit of throttle drive motor |
Always |
Below 1 V |
| OX1B (C55-88) - EX1B (C55-65) OX2B (C55-87) - EX2B (C55-64) |
W - BR B - W-B |
Heated oxygen sensor signal |
With engine speed at 2,500 rpm for 2 minutes after warming up |
Pulse generation (see waveform 2) |
| VTA2 (C55-99) - ETA (C55-97) |
W-L - P |
Throttle position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully released |
2.1 to 3.1 V |
| VTA2 (C55-99) - ETA (C55-97) |
W-L - P |
Throttle position sensor signal (for sensor malfunction detection) |
Ignition switch on (IG), Accelerator pedal fully depressed |
4.5 to 5.0 V |
| VTA1 (C55-98) - ETA (C55-97) |
Y - P |
Throttle position sensor signal (for engine control) |
Ignition switch on (IG), Throttle valve fully closed |
0.5 to 1.2 V |
| VTA1 (C55-98) - ETA (C55-97) |
Y - P |
Throttle position sensor signal (for engine control) |
Ignition switch on (IG), Throttle valve fully open |
3.2 to 4.8 V |
| THW (C55-79) - ETHW (C55-78) |
B - P |
Engine coolant temperature sensor signal |
Idling, Engine coolant temperature 80°C (176°F) |
0.2 to 1.0 V |
| THA (C55-71) - ETHA (C55-74) |
P - G-R |
Intake air temperature sensor signal |
Idling, Intake air temperature 20°C (68°F) |
0.5 to 3.4 V |
| IGF1 (C55-106) - E1 (C55-81) |
BR - W-B |
Ignition coil with igniter (ignition confirmation signal) |
Ignition switch on (IG) |
4.5 to 5.0 V |
| IGF1 (C55-106) - E1 (C55-81) |
BR - W-B |
Ignition coil with igniter (ignition confirmation signal) |
Idling |
Pulse generation (see waveform 6) |
| AICV (A55-4) - E1 (C55-81) |
V - W-B |
VSV for Air intake control system operation signal |
Ignition switch on (IG) |
9 to 14 V |
| E2G (C55-73) - E1 (C55-81) |
LG - W-B |
Earth (ground) circuit of sensor for mass air flow meter |
Always |
Below 1 V |
| VG (C55-72) - E2G (C55-73) |
L-B - LG |
Mass Air Flow (MAF) meter signal |
Idling, Shift lever position P or N, A/C switch OFF |
0.5 to 3.0 V |
| ACIS (C55-107) - E1 (C55-81) |
B-W - W-B |
VSV for ACIS (Acoustic Control Induction System) operation signal |
Ignition switch on (IG) |
9 to 14 V |
| PRG (C55-108) - E1 (C55-81) |
G-R - W-B |
Purge VSV for EVAP system operation signal |
Ignition switch on (IG) |
9 to 14 V |
| PRG (C55-108) - E1 (C55-81) |
G-R - W-B |
Purge VSV for EVAP system operation signal |
Idling |
Pulse generation (see waveform 7) |
| HA2A (C55-109) - E05 (C55-46) |
B-W - W |
A/F sensor heater operation signal |
Idling |
Below 3.0 V |
| HA2A (C55-109) - E05 (C55-46) |
B-W - W |
A/F sensor heater operation signal |
Ignition switch on (IG) |
9 to 14 V |
| HA1A (C55-86) - E04 (C55-23) |
G - W |
A/F sensor heater operation signal |
Idling |
Below 3.0 V |
| HA1A (C55-86) - E04 (C55-23) |
G - W |
A/F sensor heater operation signal |
Ignition switch on (IG) |
9 to 14 V |
| ME01 (C55-20) - E1 (C55-81) |
B - W-B |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| E03 (C55-104) - E1 (C55-81) |
B - W-B |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| HT2B (C55-47) - E1 (C55-81) HT1B (C55-48) - E1 (C55-81) |
Y - W-B LG - W-B |
Heated oxygen sensor heater operation signal |
Idling |
Below 3.0 V |
| HT2B (C55-47) - E1 (C55-81) HT1B (C55-48) - E1 (C55-81) |
Y - W-B LG - W-B |
Heated oxygen sensor heater operation signal |
Ignition switch on (IG) |
9 to 14 V |
| E05 (C55-46) - E1 (C55-81) |
W - W-B |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| E04 (C55-23) - E1 (C55-81) |
W - W-B |
Earth (ground) circuit of ECM |
Always |
Below 1 V |
| NSW (C55-62) - E1 (C55-81) |
L-B - W-B |
Park/Neutral position switch signal |
Ignition switch on (IG), Shift lever position P or N |
Below 3.0 V |
| NSW (C55-62) - E1 (C55-81) |
L-B - W-B |
Park/Neutral position switch signal |
Ignition switch on (IG), Shift lever position P or N |
9 to 14 V |
| EKN2 (C55-117) - KNK2 (C55-118) |
W - B |
Earth (ground) circuit of knock sensor |
With engine speed at 4,000 rpm after warming up |
Pulse generation (see waveform 4) |
| KNK2 (C55-118) - EKN2 (C55-117) |
B - W |
Knock sensor signal |
With engine speed at 4,000 rpm after warming up |
Pulse generation (see waveform 4) |
| A1A+ (C55-93) - E1 (C55-81) |
L - W-B |
A/F sensor signal |
Ignition switch on (IG) |
3.3 V*1
|
| A1A+ (C55-93) - E1 (C55-81) |
L - W-B |
A/F sensor signal |
Ignition switch on (IG) |
3.0 V*1
|
| A2A+ (C55-120) - E1 (C55-81) |
BR - W-B |
A/F sensor signal |
Ignition switch on (IG) |
3.3 V*1
|
| A2A+ (C55-120) - E1 (C55-81) |
BR - W-B |
A/F sensor signal |
Ignition switch on (IG) |
3.0 V*1
|
| EKNK (C55-94) - KNK1 (C55-95) |
G - R |
Earth (ground) circuit of knock sensor |
With engine speed at 4,000 rpm after warming up |
Pulse generation (see waveform 4) |
| KNK1 (C55-95) - EKNK (C55-94) |
R - G |
Knock sensor signal |
With engine speed at 4,000 rpm after warming up |
Pulse generation (see waveform 4) |
| A1A- (C55-116) - E1 (C55-81) |
P - W-B |
A/F sensor |
Ignition switch on (IG) |
3.3 V*1
|
| A1A- (C55-116) - E1 (C55-81) |
P - W-B |
A/F sensor |
Ignition switch on (IG) |
3.0 V*1
|
| A2A- (C55-119) - E1 (C55-81) |
Y - W-B |
A/F sensor |
Ignition switch on (IG) |
3.3 V*1
|
| A2A- (C55-119) - E1 (C55-81) |
Y - W-B |
A/F sensor |
Ignition switch on (IG) |
3.0 V*1
|
| OX2B (C55-87) - EX2B (C55-64) OX1B (C55-88) - EX1B (C55-65) |
B - W-B W - BR |
Heated oxygen sensor signal |
With engine speed at 2,500 rpm for 2 minutes after warming up |
Pulse generation (see waveform 2) |
| P (C55-24) - E1 (C55-81) |
B-W - W-B |
P shift position switch signal |
Ignition switch on (IG) and shift lever P position |
9 to 14 V |
| P (C55-24) - E1 (C55-81) |
B-W - W-B |
P shift position switch signal |
Ignition switch on (IG) and shift lever except P position |
Below 1 V |
| R (C55-25) - E1 (C55-81) |
P - W-B |
R shift position switch signal |
Ignition switch on (IG) and shift lever R position |
9 to 14 V |
| R (C55-25) - E1 (C55-81) |
P - W-B |
R shift position switch signal |
Ignition switch on (IG) and shift lever except R position |
Below 1 V |
| N (C55-27) - E1 (C55-81) |
L-B - W-B |
N shift position switch signal |
Ignition switch on (IG) and shift lever N position |
9 to 14 V |
| N (C55-27) - E1 (C55-81) |
L-B - W-B |
N shift position switch signal |
Ignition switch on (IG) and shift lever except N position |
Below 1 V |
| D (C55-26) - E1 (C55-81) |
G - W-B |
D shift position switch signal |
Ignition switch on (IG) and shift lever D position |
9 to 14 V |
| D (C55-26) - E1 (C55-81) |
G - W-B |
D shift position switch signal |
Ignition switch on (IG) and shift lever except D position |
Below 1 V |
| S (A55-25) - E1 (C55-81) |
Y - W-B |
S shift position switch signal |
Ignition switch on (IG) and shift lever S position |
9 to 14 V |
| S (A55-25) - E1 (C55-81) |
Y - W-B |
S shift position switch signal |
Ignition switch on (IG) and shift lever except S position |
Below 1 V |
| SFTD (A55-51) - E1 (C55-81) |
L - W-B |
Down shift switch signal |
Ignition switch on (IG) and shift lever S position |
9 to 14 V |
| SFTD (A55-51) - E1 (C55-81) |
L - W-B |
Down shift switch signal |
Ignition switch on (IG) and shift lever "-" position (Down shift) |
Below 1 V |
| SFTU (A55-16) - E1 (C55-81) |
R - W-B |
Up shift switch signal |
Ignition switch on (IG) and shift lever S position |
9 to 14 V |
| SFTU (A55-16) - E1 (C55-81) |
R - W-B |
Up shift switch signal |
Ignition switch on (IG) and shift lever "+" position (Up shift) |
Below 1 V |
| CAN+ (C55-2) - E1 (C55-81) |
B - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (see waveform 12) |
| CAN- (C55-1) - E1 (C55-81) |
Y - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (see waveform 13) |
WAVEFORM 1

Camshaft timing Oil Control Valve (OCV) operation signal
ECM Terminal Names
Between OC1+ and OC1- , OC2+ and OC2- , OE1+ and OE1- , or OE2+ and OE2-
Tester Ranges
5 V/DIV., 1 ms./DIV.
Conditions
Idling
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
WAVEFORM 2

Heated oxygen sensor signal
ECM Terminal Names
Between OX1B and EX1B, or OX2B and EX2B
Tester Ranges
0.2 V/DIV., 200 ms./DIV.
Conditions
Engine speed is maintained at 2,500 rpm for 2 minutes after sensor is warmed up
- HINT:
- In the DATA LIST, item O2S B1S2 shows the ECM values from the heated oxygen sensor.
WAVEFORM 3

Fuel injector operation signal
ECM Terminal Names
Between #10 (to #60) and E01
Tester Ranges
30 V/DIV., 20 ms./DIV.
Conditions
Idling
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
WAVEFORM 4

Knock sensor signal
ECM Terminal Names
Between KNK1 and EKNK, or KNK2 and EKN2
Tester Ranges
0.01 to 10 V/DIV., 0.01 to 10 ms./DIV.
Conditions
Engine speed is maintained at 4,000 rpm after engine is warmed up
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
- The waveforms and amplitudes displayed differ slightly depending on the vehicle.
- The wavelength becomes shorter as the engine rpm increases.
WAVEFORM 5

Variable Valve Timing (VVT) sensor signal (1)
Crankshaft position sensor signal (2)
ECM Terminal Names
(1) Between VV1+ and VV1- , VV2+ and VV2-, EV1+ and EV1-, or EV2+ and EV2-
(2) Between NE+ and NE-
Tester Ranges
5 V/DIV., 20 ms./DIV.
Conditions
Idling
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
WAVEFORM 6

Igniter IGT signal (from ECM to igniter) (1)
Igniter IGF signal (from igniter to ECM) (2)
ECM Terminal Names
(1) Between IGT (1 to 6) and E1
(2) Between IGF1 and E1
Tester Ranges
2 V/DIV., 20 ms./DIV.
Conditions
Idling
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
WAVEFORM 7

Purge VSV for EVAP system operation signal
ECM Terminal Names
Between PRG and E1
Tester Ranges
10 V/DIV., 50 ms./DIV.
Conditions
Idling
- HINT:
- If the waveform is not similar to that shown in the illustration, check the waveform again after idling for 10 minutes or more.
WAVEFORM 8

Vehicle speed signal
ECM Terminal Names
Between SPD and E1
Tester Ranges
2 V/DIV., 20 ms./DIV.
Conditions
Driving at 12 mph (20 km/h)
- HINT:
- The wavelength becomes shorter as the vehicle speed increases.
- Depending on the vehicle, the output waveform voltage may rise to 12 V if influenced by optionally installed systems.
- The wavelength becomes shorter as the vehicle speed increases.
WAVEFORM 9

Throttle drive motor operation signal (positive terminal)
ECM Terminal Names
Between M+ and ME01
Tester Ranges
5 V/DIV., 1 ms./DIV.
Conditions
Idling with warm engine
- HINT:
- The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 10

Throttle drive motor operation signal (negative terminal)
ECM Terminal Names
Between M- and ME01
Tester Ranges
5 V/DIV., 1 ms./DIV.
Conditions
Idling with warm engine
- HINT:
- The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 11

Engine speed signal
ECM Terminal Names
Between TACH and E1
Tester Ranges
5 V/DIV., 10 ms./DIV.
Conditions
Idling
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
WAVEFORM 12

CAN communication signal
ECM Terminal Names
Between CANH and E1, CAN+ and E1
Tester Ranges
1 V/DIV., 10 μsec./DIV.
Conditions
Engine stops and ignition switch on (IG)
- HINT:
- The waveform varies depending on the CAN communication signal.
WAVEFORM 13

CAN communication signal
ECM Terminal Names
Between CANL and E1, CAN- and E1
Tester Ranges
1 V/DIV., 10 μsec./DIV.
Conditions
Engine stops and ignition switch on (IG)
- HINT:
- The waveform varies depending on the CAN communication signal.