2006-2011 Camry Aurion · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built Jun 2006 – Sep 2006


1. INSTALL PARKING BRAKE PEDAL ASSEMBLY

  1. C143766
    Install the parking brake pedal assembly with the bolt and 2 nuts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. Connect the parking brake switch connector.

  1. Install the No. 1 parking brake cable assembly to the body with the bolt, the nut, and a new No. 1 parking brake cable clamp.

    C147239E02

    Torque:
    Bolt:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }
    Nut:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    Make sure that the No. 1 parking brake cable clamp is installed in the correct direction as shown in the illustration.

  1. C133438
    Using a brass bar and a hammer, install the clip to the No. 1 parking brake cable assembly.


2. CONNECT NO. 4 PARKING BRAKE CABLE ASSEMBLY
  1. Connect the No. 4 parking brake cable assembly to the No. 1 parking brake cable assembly.

  1. C143746E01
    Using SST and a wrench, hold the lock nut of the No. 1 parking brake cable and tighten the turnbuckle of the No. 4 parking brake cable assembly.
    SST
    09023-00101  

    Torque:
    without SST:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    with SST:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    2. This torque is effective when SST is parallel to a torque wrench.


3. INSTALL CENTER AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C133884E01
    Install the center airbag sensor assembly with the 3 bolts.

    Torque:
    17.5 N*m{ 179 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the center airbag sensor assembly.

  1. Connect the holder (with connectors).

  1. Check that the water-proof sheet is properly set.


4. INSTALL FLOOR SHIFT LEVER ASSEMBLY

  1. C132691
    Install the floor shift lever assembly with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


5. INSTALL FLOOR CARPET BRACKET LH

6. INSTALL FLOOR CARPET BRACKET RH

7. INSTALL NO. 1 CONSOLE BOX DUCT

  1. C129716
    Install the No. 1 console box duct with the clip.


8. INSTALL NO. 2 CONSOLE BOX INSERT FRONT

  1. B134005E01
    Engage the clip.

  1. Install the No. 2 console box insert front with the 3 screws <F>.


9. INSTALL NO. 1 CONSOLE BOX INSERT FRONT

  1. B134006E01
    Engage the clip.

  1. Install the No. 1 console box insert front with the 3 screws <F>.


10. INSTALL CONSOLE BOX ASSEMBLY

  1. B134002E01
    Install the 2 screws <F>.

  1. B149935E03
    Install the console box assembly with the 2 bolts <G>.

  1. Engage the clamp.


11. INSTALL CONSOLE BOX CARPET

  1. B134004
    Install the console box carpet.


12. INSTALL CONSOLE BOX POCKET
  1. Install the console box pocket.


13. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY
  1. Connect each connector.

  1. B141243E01
    Engage the 2 claws and 2 clips.

  1. Install the lower instrument cluster finish panel center sub-assembly with the 2 screws <F>.


14. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY

  1. B149934
    Connect the connector.

  1. Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.


15. INSTALL POSITION INDICATOR HOUSING ASSEMBLY

  1. B148447
    Engage the 6 claws and the 3 clips to install the position indicator housing assembly.


16. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144599
    Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.


17. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144605
    Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.


18. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

  1. B148448
    Install the shift lever knob sub-assembly.


19. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B133992E01
    Engage the 3 claws and 3 clips.

  1. Install the 4 screws <B>.

  1. Install the lower instrument panel sub-assembly with the bolt <A>.


20. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B133989E01
    Engage the 4 claws and 2 guides, and install the instrument panel No. 2 under cover sub-assembly.


21. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH

  1. B147264E01
    Install the air hose and connect the connector.

  1. Engage the 2 claws and the DLC3.

  1. Engage the claw and the 4 clips.

  1. Install the lower No. 1 instrument panel finish panel with the screw <B> and bolt <A>.


22. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.


23. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


24. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B132067
    Engage the 7 claws and 3 clips, then install the front door scuff plate LH.


25. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

27. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).


28. INSPECT PARKING BRAKE PEDAL TRAVEL
  1. Fully depress the parking brake pedal and release it to engage the parking brake.

  1. Depress the pedal to the floor again, and release it to disengage the parking brake.

  1. C107204
    Slowly depress the parking brake pedal to the floor, and count the number of clicks.

    Parking brake pedal travel:
    7 to 10 notches at 300 N (31 kgf, 67 lbf)


29. ADJUST PARKING BRAKE PEDAL TRAVEL
  1. Depress the parking brake pedal. Hold the No. 1 wire adjusting nut using a wrench and loosen the lock nut.

  1. Release the parking brake pedal.

  1. C133443E01
    Turn the No. 1 wire adjusting nut until the parking brake pedal travel meets the above specification.

  1. Hold the No. 1 wire adjusting nut using a wrench or an equivalent tool and tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Count the number of clicks after depressing and releasing the parking brake pedal 3 or 4 times.

  1. Check whether the parking brake drags.

  1. When operating the parking brake pedal, check that the parking brake indicator light comes on.

← REASSEMBLY (Jun 2006 – Sep 2006)COMPONENTS (Jun 2006 – Sep 2006) →