REMOVAL
Removal / installation · Vehicles built Jun 2006 – Sep 2006
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
| 2. REMOVE FRONT DOOR SCUFF PLATE LH |
Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.

| 3. REMOVE FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
Remove the cowl side trim clip.

Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH |
Remove the bolt <A> and the screw <B>.

Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.
| 7. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY |
Disengage the 4 claws.

Disengage the 2 guides and remove the No. 2 under cover sub-assembly.
| 8. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
Remove the bolt <A>.
Remove the 4 screws <B>.

Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.
| 9. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY |
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

| 10. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.

| 11. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.

| 12. REMOVE POSITION INDICATOR HOUSING ASSEMBLY |
Disengage the 6 claws and the 3 clips, and then remove the position indicator housing assembly.

| 13. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY |
Disengage the 3 claws and the 5 clips.

Disconnect the connector and remove the upper console rear panel sub-assembly.
| 14. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY |
Remove the 2 screws <F>.

Disengage the 4 claws.
Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.
- HINT:
- Set the shift lever in the D position.
| 15. REMOVE CONSOLE BOX POCKET |
Remove the console box pocket.
| 16. REMOVE CONSOLE BOX CARPET |
Remove the console box carpet.

| 17. REMOVE CONSOLE BOX ASSEMBLY |
Remove the 2 screws <F>.

Disengage the clamp.

Remove the 2 bolts <G> and the console box assembly.
| 18. REMOVE NO. 2 CONSOLE BOX INSERT FRONT |
Remove the 3 screws <F>.

Disengage the clip and remove the No. 2 console box insert front.
| 19. REMOVE NO. 1 CONSOLE BOX INSERT FRONT |
Remove the 3 screws <F>.

Disengage the clip and remove the No. 1 console box insert front.
| 20. REMOVE NO. 1 CONSOLE BOX DUCT |
Remove the clip and No. 1 console box duct.

| 21. REMOVE FLOOR CARPET BRACKET LH |
Release the clamp.

Turn back the floor carpet.
Remove the 3 clips.

Remove the floor carpet bracket LH.
| 22. REMOVE FLOOR CARPET BRACKET RH |
Release the clamp.

Turn back the floor carpet.
Remove the 3 clips.

Remove the floor carpet bracket RH.
| 23. REMOVE FLOOR SHIFT LEVER ASSEMBLY |
Remove the 4 bolts and the floor shift lever assembly.

| 24. REMOVE CENTER AIRBAG SENSOR ASSEMBLY |
Turn back the carpet.
Disconnect the holder (with connectors).

Remove the 3 bolts and center airbag sensor assembly.
| 25. DISCONNECT NO. 4 PARKING BRAKE CABLE ASSEMBLY |
Using 2 wrenches, hold the lock nut and loosen the turnbuckle.

Disconnect the No. 4 parking brake cable assembly from the No. 1 parking brake cable assembly.
| 26. REMOVE PARKING BRAKE PEDAL ASSEMBLY |
Using needle-nose pliers, remove the clip from the No. 1 parking brake cable assembly.

Remove the bolt, the nut, and the No. 1 parking brake cable clamp.


Separate the No. 1 parking brake cable assembly from the body.
Disconnect the parking brake switch connector.

Remove the bolt, 2 nuts, and the parking brake pedal assembly with the No. 1 parking brake cable assembly from the body.
