2006-2011 Camry Aurion · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.


2. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132067
    Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.


3. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


6. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B158921E01
    Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.


7. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B158913E01
    Remove the bolt <D> and the screw <F>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect each connector, and then remove the lower No. 1 instrument panel finish panel.


8. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B158922E01
    Remove the bolt <D>.

  1. Remove the screw <F> or <N>.

  1. Remove the 3 screws <F>.

  1. Disengage the 3 claws and the 3 clips, and then remove the lower instrument panel sub-assembly.


9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Smart Entry and Start System)

  1. B158917
    Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.


10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/ Smart Entry and Start System)

  1. B158918
    Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.

  1. Disconnect the connector.


11. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY

  1. B158916
    Disengage the 3 claws and the 2 clips.

  1. Disconnect each connector and remove the No. 1 instrument panel sub-assembly.


12. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B158919E01
    Remove the 2 clips.

  1. Disengage the guide and 4 claws, and then remove the instrument cluster finish panel sub-assembly.


13. REMOVE COMBINATION METER ASSEMBLY

  1. B158920
    Remove the 4 screws <B>, <C> or <H>.

  1. Disconnect each connector and remove the combination meter assembly.


14. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

  1. B159322
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


15. REMOVE UPPER CONSOLE PANEL FRONT GARNISH

  1. B158924E01
    Apply protective tape to the area shown in the illustration.

  1. B158926
    Using a moulding remover, disengage the 3 claws as shown in the illustration.

  1. B158925
    Using a moulding remover, disengage the 3 claws and remove the upper console panel front garnish as shown in the illustration.

  1. Disconnect each connector.


16. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B158929E01
    Apply protective tape to the area shown in the illustration.

  1. B158930
    Using a moulding remover, disengage the 2 claws as shown in the illustration.

  1. B158927E01
    Apply protective tape to the area shown in the illustration.

  1. B158928
    Using a moulding remover, disengage the 2 claws as shown in the illustration.

  1. B158931
    Disengage the 6 claws and remove the upper console panel sub-assembly as shown in the illustration.

  1. Disconnect the connector.


17. REMOVE CONSOLE BOX CARPET

  1. B158935
    Remove the console box carpet.


18. REMOVE CONSOLE BOX ASSEMBLY

  1. B158936E01
    Disengage the clamp.

  1. B158938
    Remove the 3 screws <H>.

  1. B158937
    Remove the 3 screws <H>.

  1. B158939
    Remove the 2 bolts <I>.

  1. B158940
    Disengage the 2 claws and remove the console box assembly.


19. REMOVE NO. 1 CONSOLE BOX DUCT

  1. C129716
    Remove the clip and No. 1 console box duct.


20. REMOVE FLOOR CARPET BRACKET LH

  1. E129146E01
    Release the clamp.

  1. Turn back the floor carpet.

  1. E128512
    Remove the 3 clips.

  1. Remove the floor carpet bracket LH.


21. REMOVE FLOOR CARPET BRACKET RH

  1. E129147E01
    Release the clamp.

  1. Turn back the floor carpet.

  1. E128513
    Remove the 3 clips.

  1. Remove the floor carpet bracket RH.


22. REMOVE YAW RATE AND ACCELERATION SENSOR

  1. C145963
    Disconnect the yaw rate and acceleration sensor connector.

  1. Remove the 2 bolts and yaw rate and acceleration sensor.

  1. C145964
    Remove the 2 nuts and yaw rate and acceleration sensor from the bracket.


23. REMOVE FLOOR SHIFT LEVER ASSEMBLY

  1. C224889
    Remove the 4 bolts and floor shift lever assembly.


24. REMOVE CENTER AIRBAG SENSOR ASSEMBLY
  1. Turn back the carpet.

  1. C133884
    Disconnect the holder (with connectors).

  1. Remove the 3 bolts and center airbag sensor assembly.


25. DISCONNECT NO. 4 PARKING BRAKE CABLE ASSEMBLY

  1. C132693E01
    Using 2 wrenches, hold the lock nut and loosen the turnbuckle.

  1. Disconnect the No. 4 parking brake cable assembly from the No. 1 parking brake cable assembly.


26. REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY

  1. C133448
    Disengage the 3 claws and remove the No. 1 air duct sub-assembly.


27. REMOVE PARKING BRAKE PEDAL ASSEMBLY

  1. C132692
    Using needle-nose pliers, remove the clip from the No. 1 parking brake cable assembly.

  1. C133447
    Remove the bolt.

  1. C132690
    Disconnect the parking brake switch connector.

  1. Remove the bolt, 2 nuts, and the parking brake pedal assembly with the No. 1 parking brake cable assembly from the body.

← REMOVAL (Oct 2006 – May 2009)DISASSEMBLY (Oct 2006 – May 2009) →