Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Remove the radiator cap sub-assembly from the radiator assembly.
Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs, then drain the coolant.
HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.
5.
REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH
Remove the nut and the front wiper arm and blade assembly LH.
6.
REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH
Remove the nut and the front wiper arm and blade assembly RH.
7.
REMOVE FRONT FENDER TO COWL SIDE SEAL LH
Disengage the claw and remove the front fender to cowl side seal LH.
8.
REMOVE FRONT FENDER TO COWL SIDE SEAL RH
Disengage the claw and remove the front fender to cowl side seal RH.
9.
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)
Remove the 2 clips.
Disengage the 4 claws and remove the cowl top ventilator louver sub-assembly.
10.
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)
Remove the 2 clips.
Disengage the 3 claws and remove the cowl top ventilator louver sub-assembly.
11.
REMOVE WINDSHIELD WIPER MOTOR AND LINK
Disconnect the connector.
Remove the 4 bolts and the windshield wiper motor and link assembly.
12.
REMOVE COWL TOP PANEL OUTER SUB-ASSEMBLY
Remove the 4 bolts, 4 nuts and cowl top panel outer sub-assembly.
13.
REMOVE COOL AIR INTAKE DUCT SEAL
Remove the 7 clips and intake duct seal.
14.
REMOVE V-BANK COVER SUB-ASSEMBLY
Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.
NOTICE:
Attempting to disengage both front and rear clips at the same time may cause the cover to break.
15.
REMOVE AIR CLEANER INLET ASSEMBLY
Remove the 2 bolts, clamp and air cleaner inlet.
16.
REMOVE AIR CLEANER CAP SUB-ASSEMBLY
Disconnect the 3 vacuum hoses.
Disconnect the mass air flow meter connector (*1).
Disconnect the No. 2 ventilation hose (*2).
Disconnect the hose band (*3).
Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.
17.
REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Disconnect the vacuum hose and hose clamp.
Remove the 3 bolts and air cleaner case.
18.
REMOVE NO. 1 AIR CLEANER INLET
Remove the bolt and No. 1 air cleaner inlet.
19.
REMOVE INTAKE AIR SURGE TANK
Disconnect the 2 water by-pass hoses from the throttle with motor body assembly. (*1)
Disconnect the vapor feed hose. (*2)
Disconnect the throttle with motor body assembly connector and clamp. (*3)
Disconnect the No. 1 ventilation hose. (*4)
Disconnect the union to check valve hose. (*5)
Remove the bolt and vacuum hose clamp.
Disconnect the connector.
Using a 5 mm hexagon socket wrench, remove the 4 bolts. (*1)
Remove the 2 nuts, 2 bolts and intake air surge tank. (*2)
Remove the gasket from the intake air surge tank.
20.
DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the No. 2 fuel pipe clamp.
Pinch the tube connector and then pull out the fuel pipe.
NOTICE:
Check that there is no dirt or other foreign objects around the connector before this operation and clean the connector as necessary.
It is necessary to prevent mud or dirt from entering the quick connector. If mud enters the connector, the O-rings may not seal properly.
Remove the quick connector by hand.
Do not bend, kink, or twist the nylon tube. Protect the connector by covering it with a plastic bag.
If the pipe and the connector are stuck, try wiggling or pushing and pulling the connector to release it and pull the connector out of the pipe carefully.
21.
REMOVE INTAKE MANIFOLD
Uniformly loosen and remove the 6 bolts and 4 nuts.