2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built Jun 2006 – Sep 2006


1. PRECAUTION
(Click here)

2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment (Click here).


4. REMOVE LOWER NO. 3 STEERING WHEEL COVER

  1. Using a screwdriver, disengage the claw and remove the No. 3 lower steering wheel cover.

    C146012E01

    HINT:
    Tape up the screwdriver tip before use.


5. REMOVE LOWER NO. 2 STEERING WHEEL COVER

  1. Using a screwdriver, disengage the claw and remove the No. 2 lower steering wheel cover.

    C146013E01

    HINT:
    Tape up the screwdriver tip before use.


6. REMOVE STEERING PAD

  1. Using a "TORX" socket (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.

    C146014E01

  1. C133859E01
    Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector from the steering pad.

  1. Disconnect the 2 airbag connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


7. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and the steering main shaft.

  1. Disconnect the connectors from the spiral cable.

  1. C145839E01
    Using SST, remove the steering wheel assembly.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)


8. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132067
    Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.


9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B147264E01
    Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.


11. REMOVE STEERING COLUMN COVER

  1. B137294E01
    Remove the 2 screws <D>.

  1. Disengage the 2 claws and remove the lower steering column cover.

  1. Disengage the claw and remove the upper steering column cover.


12. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.

  1. C145843
    Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.


13. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL

  1. B144612
    Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.


14. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B133985E01
    Remove the 2 clips.

  1. Disengage the guide and 4 claws, and then remove the instrument cluster finish panel sub-assembly.


15. REMOVE COMBINATION METER ASSEMBLY

  1. B152781E01
    Remove the 4 screws <E>.

  1. Disconnect each connector and remove the combination meter assembly.


16. REMOVE FRONT DOOR SCUFF PLATE RH

17. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

18. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B133988E01
    Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.


19. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Remove the bolt <A>.

  1. B133992E01
    Remove the 4 screws <B>.

  1. Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.


20. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

  1. B152779
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


21. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144605
    Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.


22. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144599
    Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.


23. REMOVE POSITION INDICATOR HOUSING ASSEMBLY

  1. B152776E01
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B152777
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the position indicator housing assembly as shown in the illustration.


24. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY

  1. B144604
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


25. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY

  1. B141243E01
    Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.

    HINT:
    Set the shift lever in the D position.


26. REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY

  1. B152782E01
    Apply protective tape to the areas shown in the illustration.

  1. B152783
    Using a moulding remover, disengage the 3 clips.

  1. B152784
    Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the instrument panel No. 2 register assembly.


27. REMOVE NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY

  1. E137564
    Remove the 4 bolts.

  1. Pull the navigation receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver with heater control panel assembly.


28. REMOVE CONSOLE BOX POCKET
  1. Remove the console box pocket.


29. REMOVE CONSOLE BOX CARPET

  1. B134004
    Remove the console box carpet.


30. REMOVE CONSOLE BOX ASSEMBLY

  1. B134002E01
    Remove the 2 screws <F>.

  1. B149935E03
    Disengage the clamp.

  1. Remove the 2 bolts <G> and the console box assembly.


31. REMOVE NO. 2 CONSOLE BOX INSERT FRONT

  1. B134005E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 2 console box insert front.


32. REMOVE NO. 1 CONSOLE BOX INSERT FRONT

  1. B134006E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 1 console box insert front.


33. REMOVE FRONT PILLAR GARNISH LH

  1. B132056E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish LH.

  1. Remove the clip <A> from the vehicle body.

  1. B132100E02
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


34. REMOVE INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY

  1. B134007
    Disengage the 4 clips and remove the instrument panel No. 1 register assembly.


35. REMOVE INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY

  1. B134009E01
    Disengage the 6 claws and the 2 clips.

  1. Disengage the 2 guides and remove the instrument panel No. 1 speaker panel sub-assembly.


36. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH

  1. E129167
    Remove the 2 bolts and front No. 2 speaker assembly.

  1. Disconnect the connector.


37. REMOVE FRONT PILLAR GARNISH RH

  1. B132055E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish RH.

  1. Remove the clip <A> from the vehicle body.

  1. B132099E02
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


38. REMOVE INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY

  1. B134008
    Disengage the 4 clips and remove the instrument panel No. 3 register assembly.


39. REMOVE INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY

  1. B134010E01
    Disengage the 6 claws and the 2 clips.

  1. Disengage the 2 guides and remove the instrument panel No. 2 speaker panel sub-assembly.


40. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side (Click here).


41. REMOVE NO. 1 DEFROSTER NOZZLE GARNISH

  1. B134011E01
    Disengage the 8 clips and the 4 guides.

  1. Disconnect each connector and remove the No. 1 defroster nozzle garnish.


42. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY

  1. C132564E01
    Disconnect the connector (yellow colored one).


43. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Disengage each clamp.

  1. Disconnect each connector.

  1. Remove the bolt <J>.

  1. Remove the 2 passenger airbag bolts <C>.

    B134013E01

  1. Remove the 2 bolts <H>.

  1. Remove the 2 nuts <I>.

  1. Disengage the 5 claws and remove the instrument panel safety pad assembly.

    B134014E06


44. REMOVE SIDE NO. 1 DEFROSTER NOZZLE DUCT

  1. B134016E02
    Remove the screw <F> and the side No. 1 defroster nozzle duct.


45. REMOVE SIDE NO. 2 DEFROSTER NOZZLE DUCT

  1. B134017E02
    Remove the screw <F> and the side No. 2 defroster nozzle duct.


46. REMOVE DEFROSTER NOZZLE ASSEMBLY

  1. B134018E02
    Remove the 3 screws <F> and the defroster nozzle assembly.


47. REMOVE NO. 1 HEATER TO REGISTER DUCT

  1. B134019E02
    Remove the 3 screws <F> and the No. 1 heater to register duct.


48. REMOVE NO. 3 HEATER TO REGISTER DUCT

  1. B134020E02
    Remove the 3 screws <F> and the No. 3 heater to register duct.


49. REMOVE NO. 2 HEATER TO REGISTER DUCT

  1. B134021E02
    Remove the 2 screws <F> and the No. 2 heater to register duct.


50. REMOVE NAVIGATION ANTENNA ASSEMBLY
  1. Disengage the 3 clamps.

  1. E136419E01
    Remove the 2 screws and navigation antenna assembly.

← COMPONENTS (Jun 2006 – Sep 2006)INSTALLATION (Jun 2006 – Sep 2006) →