2006-2011 Camry Aurion · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132068
    Disengage the 5 claws and 2 clips, and remove the rear door scuff plate LH.


3. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


4. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B158913E01
    Remove the bolt <D> and the screw <F>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect each connector, and then remove the lower No. 1 instrument panel finish panel.


5. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


7. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B158921E01
    Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.


8. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B158922E01
    Remove the bolt <D>.

  1. Remove the screw <F> or <N>.

  1. Remove the 3 screws <F>.

  1. Disengage the 3 claws and the 3 clips, and then remove the lower instrument panel sub-assembly.


9. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

  1. C147376
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


10. REMOVE UPPER CONSOLE PANEL FRONT GARNISH

  1. B158924E01
    Apply protective tape to the area shown in the illustration.

  1. B158926
    Using a moulding remover, disengage the 3 claws as shown in the illustration.

  1. B158925
    Using a moulding remover, disengage the 3 claws and remove the upper console panel front garnish as shown in the illustration.

  1. Disconnect each connector.


11. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B158929E01
    Apply protective tape to the area shown in the illustration.

  1. B158930
    Using a moulding remover, disengage the 2 claws as shown in the illustration.

  1. B158927E01
    Apply protective tape to the area shown in the illustration.

  1. B158928
    Using a moulding remover, disengage the 2 claws as shown in the illustration.

  1. B158931
    Disengage the 6 claws and remove the upper console panel sub-assembly as shown in the illustration.

  1. Disconnect the connector.


12. REMOVE CONSOLE BOX CARPET

  1. B158935
    Remove the console box carpet.


13. REMOVE CONSOLE BOX ASSEMBLY

  1. B158936E01
    Disengage the clamp.

  1. B158938
    Remove the 3 screws <H>.

  1. B158937
    Remove the 3 screws <H>.

  1. B158939
    Remove the 2 bolts <I>.

  1. B158940
    Disengage the 2 claws and remove the console box assembly.


14. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Disconnect the end of the transmission control cable assembly from the shift lever assembly.

  1. C148659
    Disconnect the transmission control cable assembly from the shift lever assembly.


15. REMOVE SHIFT LEVER ASSEMBLY

  1. C148665
    Disconnect the shift lock control ECU connector and transmission control switch wire connector.

  1. C148666
    Remove the 4 bolts and shift lever assembly.

← ON-VEHICLE INSPECTION (from Oct 2006)REMOVAL (from Jun 2009) →