2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built Jun 2006 – Sep 2006


1. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B148446
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B152779
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

  1. B152774
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


4. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144605
    Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.


5. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144599
    Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.


6. REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle LHD)

  1. B148447
    Disengage the 6 claws and the 3 clips, and then remove the position indicator housing assembly.


7. REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle RHD)

  1. B152776E01
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B152777
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the position indicator housing assembly as shown in the illustration.


8. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)

  1. B144607E01
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B144602
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.


9. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B149934
    Disengage the 3 claws and the 5 clips.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.


10. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B144604
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


11. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)

  1. B144604
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


12. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY

  1. B141243E01
    Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.

    HINT:
    Set the shift lever in the D position.


13. REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY

  1. B152782E01
    Apply protective tape to the areas shown in the illustration.

  1. B152783
    Using a moulding remover, disengage the 3 clips.

  1. B152784
    Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the instrument panel No. 2 register assembly.


14. REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ CD Player)

  1. E129175
    Remove the 4 bolts.

  1. Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver with heater control panel assembly.


15. REMOVE RADIO NO. 1 BRACKET (w/ CD Player)

  1. E129176
    Remove the 3 bolts, 2 screws, and radio No. 1 bracket.


16. REMOVE RADIO NO. 2 BRACKET (w/ CD Player)

  1. E129177
    Remove the 3 bolts, 2 screws, and radio No. 2 bracket.


17. REMOVE RADIO RECEIVER ASSEMBLY (w/ CD Player)

  1. E129178
    Remove the radio receiver assembly as shown in the illustration.


18. REMOVE RADIO AND CASSETTE TAPE WITH HEATER CONTROL PANEL ASSEMBLY (w/o CD Player)

  1. E135568
    Remove the 4 bolts.

  1. Pull the radio and cassette tape with heater control panel assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the radio and cassette tape with heater control panel assembly.


19. REMOVE RADIO NO. 1 BRACKET (w/o CD Player)

  1. E135569
    Remove the 2 bolts, 3 screws, radio receiver panel, and radio No. 1 bracket.


20. REMOVE RADIO NO. 2 BRACKET (w/o CD Player)

  1. E135570
    Remove the 2 bolts, 3 screws, radio receiver panel, and radio No. 2 bracket.


21. REMOVE RADIO AND CASSETTE TAPE ASSEMBLY (w/o CD Player)
← COMPONENTS (Jun 2006 – Sep 2006)INSTALLATION (Jun 2006 – Sep 2006) →