2006-2011 Camry Aurion · Service Manual BODY

Power Window Master Switch Circuit

Circuit diagnosis · Vehicles built from Oct 2006

Versions by build date: Jun 2006 – Sep 2006 from Oct 2006

DESCRIPTION

This circuit transmits signal from the power window regulator master switch assembly to the power window regulator switch.

WIRING DIAGRAM

B140723E04
B153699E03

INSPECTION PROCEDURE


1. CHECK DTC OUTPUT
  1. Turn the ignition switch off.

  1. Wait for at least 10 seconds, and then turn the ignition switch on (IG).

  1. Check whether the DTC output recurs.

    Result:
    Display (DTC output)
    Proceed to
    No output
    A
    Output DTCs
    B



B
GO TO DTC CHART
A


2. INSPECT WIRE HARNESS (WINDOW REGULATOR MASTER SWITCH - BATTERY AND BODY GROUND)

  1. B137060E08
    Disconnect the M1 (*1), L1 (*2) connector.

    HINT:
    1. *1: LHD models
    2. *2: RHD models

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    6 (B) - Body ground
    Ignition switch on (IG)
    10 to 14 V


    Standard resistance:
    LHD models:
    Tester Connection
    Condition
    Specified Condition
    1 (E) - Body ground
    Always
    Below 1 Ω
    RHD models:
    Tester Connection
    Condition
    Specified Condition
    9 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

  1. B150505E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    (LHD models with Jam Protection):
    Tester Connection
    Condition
    Specified Condition
    8 (U) - 1 (E) - 4 (A)
    Auto UP
    Below 1 Ω
    8 (U) - 1 (E)
    Manual UP
    Below 1 Ω
    8 (U) - 5 (D) - 6 (B)
    OFF
    Below 1 Ω
    5 (D) - 1 (E)
    Manual DOWN
    Below 1 Ω
    4 (A) - 5 (D) - 1 (E)
    Auto DOWN
    Below 1 Ω
    1 (E) - 10 (U)
    Lock/Unlock switch
    UNLOCK (Below 1 Ω) → LOCK (10 kΩ or higher)
    1 (E) - 12 (U)
    1 (E) - 13 (D)
    1 (E) - 15 (D)
    1 (E) - 16 (U)
    1 (E) - 18 (D)
    (RHD models):
    Tester Connection
    Condition
    Specified Condition
    1 (U) - 9 (E) - 4 (A)
    Auto UP
    Below 1 Ω
    1 (U) - 9 (E)
    Manual UP
    Below 1 Ω
    1 (U) - 5 (D) - 6 (B)
    OFF
    Below 1 Ω
    5 (D) - 9 (E)
    Manual DOWN
    Below 1 Ω
    4 (A) - 5 (D) - 9 (E)
    Auto DOWN
    Below 1 Ω
    9 (E) - 16 (U)
    Lock/Unlock switch
    UNLOCK (Below 1 Ω) → LOCK (10 kΩ or higher)
    9 (E) - 18 (U)
    9 (E) - 10 (D)
    9 (E) - 13 (D)
    9 (E) - 12 (U)
    9 (E) - 15 (D)
    (LHD models without Jam Protection):
    Tester Connection
    Condition
    Specified Condition
    1(E) - 3 (U)
    OFF
    Below 1 Ω
    1 (E) - 4 (D)
    Below 1 Ω
    1 (E) - 10 (U)
    Lock/Unlock switch
    UNLOCK (Below 1 Ω) → LOCK (10kΩ or higher)
    1 (E) - 12 (U)
    1 (E) - 13 (D)
    1 (E) - 15 (D)
    1 (E) - 16 (U)
    1 (E) - 18 (D)



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


4. CHECK WIRE HARNESS (MASTER SWITCH - FRONT PASSENGER, REAR LH/RH SWITCH)

  1. B137067E06
    LHD models:Disconnect the M1, H6, K1 and J1 connectors.
    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Front passenger side:
      Tester Connection
      Condition
      Specified Condition
      M1-16 (U) - H6-5 (SU)
      Always
      Below 1 Ω
      M1-15 (D) - H6-2 (SD)
      Always
      Below 1 Ω
      M1-16 (U) - Body ground
      Always
      10 kΩ or higher
      M1-15 (D) - Body ground
      Always
      10 kΩ or higher
      Rear LH side:
      Tester Connection
      Condition
      Specified Condition
      M1-12 (U) - K1-5 (SU)
      Always
      Below 1 Ω
      M1-13 (D) - K1-2 (SD)
      Always
      Below 1 Ω
      M1-12 (U) - Body ground
      Always
      10 kΩ or higher
      M1-13 (D) - Body ground
      Always
      10 kΩ or higher
      Rear RH side:
      Tester Connection
      Condition
      Specified Condition
      M1-10 (U) - J1-5 (SU)
      Always
      Below 1 Ω
      M1-18 (D) - J1-2 (SD)
      Always
      Below 1 Ω
      M1-10 (U) - Body ground
      Always
      10 kΩ or higher
      M1-18 (D) - Body ground
      Always
      10 kΩ or higher

  1. B137067E07
    RHD models:Disconnect the L1, H6, K1 and J1 connectors.
    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Front passenger side:
      Tester Connection
      Condition
      Specified Condition
      L1-12 (U) - I9-5 (SU)
      Always
      Below 1 Ω
      L1-13(D) - I9-2 (SD)
      Always
      Below 1 Ω
      L1-12 (U) - Body ground
      Always
      10 kΩ or higher
      L1-13 (D) - Body ground
      Always
      10 kΩ or higher
      Rear LH side:
      Tester Connection
      Condition
      Specified Condition
      L1-18 (U) - K1-5 (SU)
      Always
      Below 1 Ω
      L1-10 (D) - K1-2 (SD)
      Always
      Below 1 Ω
      L1-18 (U) - Body ground
      Always
      10 kΩ or higher
      L1-10 (D) - Body ground
      Always
      10 kΩ or higher
      Rear RH side:
      Tester Connection
      Condition
      Specified Condition
      L1-16 (U) - J1-5 (SU)
      Always
      Below 1 Ω
      L1-15 (D) - J1-2 (SD)
      Always
      Below 1 Ω
      L1-16 (U) - Body ground
      Always
      10 kΩ or higher
      L1-15 (D) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Power Window Master Switch Circuit (Jun 2006 – Sep 2006)Front Passenger Side Power Window Switch Power Source Circuit (Jun 2006 – Sep 2006) →