2006-2011 Camry Aurion · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY

  1. B152077
    Install the rear bumper reinforcement sub-assembly with the 6 nuts.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }


2. INSTALL WHEEL HOUSE REINFORCEMENT LH

  1. B149455
    Install the wheel house reinforcement LH with the nut.


3. INSTALL WHEEL HOUSE REINFORCEMENT RH

HINT:
Use the same procedure for the RH side and LH side.


4. INSTALL REAR BUMPER SIDE RETAINER LH

  1. B149454E01
    Engage the claw and guide, and install the rear bumper side retainer LH.

  1. Install the 2 screws.


5. INSTALL REAR BUMPER SIDE RETAINER RH

HINT:
Use the same procedure for the RH side and LH side.


6. INSTALL REAR BUMPER SIDE SUPPORT LH

  1. B149453E01
    Engage the claw and 2 guides, and install the rear bumper side support LH.

  1. Install the 2 screws.


7. INSTALL REAR BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure for the RH side and LH side.


8. INSTALL REFLEX REFLECTOR ASSEMBLY LH

  1. B149457E02
    Install the reflex reflector assembly LH with the screw.


9. INSTALL REFLEX REFLECTOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.


10. INSTALL REAR BUMPER PLATE LH

11. INSTALL REAR BUMPER PLATE RH

12. INSTALL REAR BUMPER EXTENSION LH (w/ Rear Lower Spoiler)

  1. B159636
    Install the rear bumper extension LH with the 2 nuts.


13. INSTALL REAR BUMPER EXTENSION RH (w/ Rear Lower Spoiler)

HINT:
Use the same procedure for the RH side and LH side.


14. INSTALL REAR LOWER SPOILER (w/ Rear Lower Spoiler)

  1. Engage the 16 claws and install the rear lower spoiler.

    B159637

  1. Install the 16 clips, 4 nuts and 2 screws.


15. INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ Clearance Sonar System)

16. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ Clearance Sonar System)

  1. E134863E01
    Install the No. 2 ultrasonic sensor retainer to the rear bumper.

    NOTICE:
    Do not damage the bumper with the snap when installing the retainer.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.


17. INSTALL NO. 2 ULTRASONIC SENSOR (w/ Clearance Sonar System)

  1. E135369
    Engage the 2 claws and install the No. 2 ultrasonic sensor.

  1. E135370
    Install the sensor retainer as shown in the illustration.

  1. Connect the sensor connector.


18. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Clearance Sonar System)

  1. E135552E01
    Install the No. 1 ultrasonic sensor retainer to the rear bumper.

    NOTICE:
    Do not damage the bumper with the snap when installing the retainer.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.


19. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Clearance Sonar System)

  1. E135368
    Engage the 2 claws and install the No. 1 ultrasonic sensor.

  1. Connect the sensor connector.

← DISASSEMBLY (from Jun 2009)REASSEMBLY (from Jun 2009) →