2006-2011 Camry Aurion · Service Manual TRANSMISSION

P0791 Intermediate Shaft Speed Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built from Oct 2006

Also covers:

DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input speed of the transaxle. By comparing the input turbine speed signal (NC) with the counter gear speed sensor signal (NC), the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, thus, providing smooth gear shifts.
C133216E01
DTC No.
DTC Detection Condition
Trouble Area
P0791
When the speed sensor input voltage is either more than 1.9 V or less than 0.1 V for 2 seconds or more.
  1. Transmission revolution sensor (speed sensor NC)
  2. TCM
P0793
When the vehicle speed is 25 km/h (15.5 mph) or higher, the counter gear speed is less than 300 rpm for 2 seconds or more.

MONITOR DESCRIPTION

The NT terminal of the TCM detects a revolution signal from the speed sensor (NT) (input RPM). The TCM calculates a gearshift comparing the speed sensor (NT) with the speed sensor (NC).
While the vehicle is operating in 2nd, 3rd, 4th or 5th gear in the D position, if the input shaft revolution is less than 300 rpm *1 although the output shaft revolution is more than 1,000 rpm *2, the TCM interprets this as a fault, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM

C133260E05

INSPECTION PROCEDURE


DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty.

HINT:
According to the Data List displayed on the intelligent tester, you can read the value of switches, sensors, actuators and other items without removing any parts. Reading the Data List as the first step in troubleshooting is one method to save diagnostic time.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn on the tester.

  6. Enter the following items: "Powertrain / ECT / Data List".

  7. According to the display on the tester, read "Data List".

    Tester Display
    Measurement Item/Range
    Normal Condition
    SPD (NC)
    Counter Gear Speed/Display: 50 r/min

    HINT:
    1. Lock-up ON (after warming up the engine); input turbine speed (NC) is equal to the engine speed.
    2. Lock-up OFF (idling at N position); input turbine speed (NC) is nearly equal to the engine speed.

    HINT:
    1. SPD (NC) is always 0 while driving: Open or short in the sensor or circuit.
    2. SPD (NC) is always between 0 and 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.


1. INSPECT SPEED SENSOR (SENSOR INSTALLATION)

  1. C133219
    Make sure that the connector is properly connected, and check the speed sensor installation.

    OK:
    The installation bolts are tightened properly and there is no clearance between the sensor and transaxle case.



NG
REPAIR OR REPLACE SPEED SENSOR
OK


2. CHECK TRANSMISSION WIRE

  1. C133270E02
    Remove the TCM.

  1. Disconnect the speed sensor connector from the transmission wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Condition
    Specified Condition
    3 (NCO) - 3 (NCO)
    Below 1 Ω
    4 (NCB) - 4 (NCB)
    Below 1 Ω
    3 (NCO) - 4 (NCB)
    10 kΩ or higher



NG
REPLACE TRANSMISSION WIRE
OK


3. REPLACE SPEED SENSOR

NEXT


4. CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0791 AND/OR P0793 IS OUTPUT AGAIN)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the intelligent tester main switch ON.

  1. Perform the monitor drive pattern (Click here).

  1. When using the intelligent tester:Enter the following items "Powertrain / ECT / DTC / Current or Pending".

  1. Read the DTCs using the intelligent tester.

    Result:
    Display (DTC output)
    Proceed to
    Only "P0791 or P0793" is output
    A
    No output
    B



B
END
A

REPLACE TCM


← P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2) (from Oct 2006)P0796 Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3) (Oct 2006 – May 2009) →