2006-2011 Camry Aurion · Service Manual HEATER & AIR CONDITIONING SYSTEM

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B148446
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B152779
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

  1. B152774
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


4. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for 2GR-FE RHD)

  1. B159322
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (except 2GR-FE RHD)

  1. B144605
    Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.


6. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (except 2GR-FE RHD)

  1. B144599
    Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.


7. REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle LHD)

  1. B148447
    Disengage the 6 claws and the 3 clips, and then remove the position indicator housing assembly.


8. REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle RHD)

  1. B152776E01
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B152777
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the position indicator housing assembly as shown in the illustration.


9. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)

  1. B144607E02
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B144602
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.


10. REMOVE UPPER CONSOLE PANEL FRONT GARNISH (for 2GR-FE RHD)

  1. B158924E01
    Apply protective tape to the area shown in the illustration.

  1. B158926
    Using a moulding remover, disengage the 3 claws as shown in the illustration.

  1. B158925
    Using a moulding remover, disengage the 3 claws and remove the upper console panel front garnish as shown in the illustration.

  1. Disconnect each connector.


11. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B149934
    Disengage the 3 claws and the 5 clips.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.


12. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B144604
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


13. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)

  1. B144604
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


14. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (for 2GR-FE RHD)

  1. B158929E01
    Apply protective tape to the area shown in the illustration.

  1. B158930
    Using a moulding remover, disengage the 2 claws as shown in the illustration.

  1. B158927E01
    Apply protective tape to the area shown in the illustration.

  1. B158928
    Using a moulding remover, disengage the 2 claws as shown in the illustration.

  1. B158931
    Disengage the 6 claws and remove the upper console panel sub-assembly as shown in the illustration.

  1. Disconnect the connector.


15. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY (except 2GR-FE RHD)

  1. B141243E01
    Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.

    HINT:
    Set the shift lever in the D position.


16. REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY (except 2GR-FE RHD)

  1. B152782E01
    Apply protective tape to the areas shown in the illustration.

  1. B152783
    Using a moulding remover, disengage the 3 clips.

  1. B152784
    Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the instrument panel No. 2 register assembly.


17. REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY (for 2GR-FE RHD)

  1. B158932E01
    Apply protective tape to the areas shown in the illustration.

  1. B158934
    Using a moulding remover, disengage the 6 claws as shown in the illustration.

  1. B158933
    Using a moulding remover, disengage the 5 claws as shown in the illustration.

  1. Disconnect each connector and remove the instrument panel No. 2 register assembly.


18. REMOVE RADIO AND CASSETTE TAPE WITH HEATER CONTROL PANEL ASSEMBLY

  1. E135568
    Remove the 4 bolts.

  1. Pull the radio and cassette tape with heater control panel assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the radio and cassette tape with heater control panel assembly.


19. REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ CD Player)

  1. E129175
    Remove the 4 bolts.

  1. Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver with heater control panel assembly.


20. REMOVE RADIO NO. 1 BRACKET (w/ CD Player)

  1. E129176
    Remove the 3 bolts, 2 screws, and radio No. 1 bracket.


21. REMOVE RADIO NO. 1 BRACKET (w/o CD Player)

  1. E135569
    Remove the 2 bolts, 3 screws, radio receiver panel, and radio No. 1 bracket.


22. REMOVE RADIO NO. 2 BRACKET (w/ CD Player)

  1. E129177
    Remove the 3 bolts, 2 screws, and radio No. 2 bracket.


23. REMOVE RADIO NO. 2 BRACKET (w/o CD Player)

  1. E135570
    Remove the 2 bolts, 3 screws, radio receiver panel, and radio No. 2 bracket.


24. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/ CD Player)

  1. E128541
    Remove the air conditioning control assembly as shown in the illustration.


25. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/o CD Player)

  1. E135685
    Remove the air conditioning control assembly as shown in the illustration.

← REMOVAL (Jun 2006 – Sep 2006)REMOVAL (from Jun 2009) →